Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
I tried to set the Mode Switch to the service position, but no use.
Please help! Thank you!
Last edited by aixlover; 05-13-2011 at 09:18 AM..
Reason: add more info
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
Hi, I am now trying to setup XSCF mail reporting for a Sun M5K. There is no mail server here. Each Sun box is both its mail receiver and sender by using mailx. Mailx is working fine on this M5K.
XSCF> setsmtp
Mail Server :
Port :
Authentication Mechanism :
Reply Address:
What should I... (4 Replies)
Hi,
This Sun M5000 currently has a single domain (0) created. Solaris 10 is installed on this domain with some local zones. Now we need to add a secondary hardware domain (1) to this M5000. My question: Can we keep the current OS settings on domain 0 when adding the secondary domain 1?
... (0 Replies)
Hi,
This Sun M5000 currently has a single domain (0) created. Solaris 10 is installed on this domain with some local zones. Now we need to add a secondary hardware domain (1) to this M5000. My question: Can we keep the current OS settings on domain 0 when adding the secondary domain 1?
Thank... (5 Replies)
Hi,
I've configured this Sun M5000 to use two system domains (added a second domain to it). The following is the info about the settings. The showdevices command can't show devices on domain 1 because Solaris is not loaded on it yet.
My question: How can I confirm the hardware devices such as... (5 Replies)
I have an M5K with disk issues I'm trying to troubleshoot, and it's causing me some confusion. I know the host has four on-board HDDs, but the format command's output shows c0t0d0, c0t1d0, c3t0d0, and c3t1d0. cfgadm -al shows c0t3d0 as the DVD-ROM drive, and c1 and c2 as SAN disks. Confused yet?
... (2 Replies)
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Trying to update my M5000 firmware. trying to mount my USB to upload firmware and getting the following message.
XSCF> getflashimage -v file:///media/usb_msd/FFXCP1115.tar.gz
Free space: 97MB
Making sure mount point is clear
umount: /media/usb_msd is not mounted (according to mtab)
Trying... (2 Replies)
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)