I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output.
You haven't said which system you use but from the output format i suppose it is some Linux-derivate.
It is common to configure network interfaces in via scripts/scriptlets in /etc/sysconfig/... but i suppose (part of) your configuration (the old part) is/was also duplicated in some other part of the system initialisation, probably in some rc-script somewhere in /etc/rc.d. Perhaps this didn't show p because the two competing configurations were effectively the same. Now that you have changed one of them they create two different configurations.
If this is the case you should simply remove that other configuration and rely on /etc/sysconfig and the procedures using it.
Hi gurus,
In a few month, we must enable IPv6 on our Linux Server!
Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files?
Could Linux run simultaneous IPv4 and IPv6?
Thanks in advance for our help our ideas?
Best regards,
nm (3 Replies)
Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Hi,
Apologies if this is the wrong forum or this question has been answered already.
I'm using the ISC dhcpd server on Centos 6.0, and can happily assign a single IPV6 address to a client with entries like this:
subnet6 fd01:0:0:5::/64
{
option dhcp6.name-servers fd01:0:0:5::226;... (0 Replies)
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
HI all,
First post on the forum, and my first proper project on the Paspberry Pi, so sorry if this is in the wrong place.
I am trying to turn my Pi in to a 3G/4G Bonding router. I have been researching and trying this for a week or so now. The basic plan is to have up to 6 ZTE MF823 USB... (0 Replies)
Hello Dears ,
please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface .
Thanks in... (1 Reply)
I'm running a Linux OS that uses Debian as it's base. A commercial vpn is installed that uses OpenVPN. For some reason, I can't get ipv6 to tunnel properly .... and Ipleak.net shows that my location is being unmasked by ipv6.
I've tried kernel commands at boot, I've tried sysctl.conf commands.... (2 Replies)
Discussion started by: benc
2 Replies
LEARN ABOUT CENTOS
bond2team
BOND2TEAM(1) Bonding to Team conversion tool BOND2TEAM(1)NAME
bond2team -- Converts bonding configuration to team
SYNOPSIS
bond2team [options]
DESCRIPTION
bond2team is a tool to convert bonding options to team trying as much as possible to keep the original functionality.
The resulting files are saved in a temporary directory using ifcfg style by default. In the case of converting an ifcfg file, it translates
the bonding options to team, preserving all other options. In that case, it converts the respective slave ifcfg files to team port, pre-
serving all their other options too. In case of converting from given bonding options in the command line, the tool can use the specified
ports as team ports.
OPTIONS --master <interface>
Specify the interface name or ifcfg file to convert. If the interface name is specified, the tool will look at
/etc/sysconfig/network-scripts/ for the respective ifcfg file.
--rename <interface>
This is a convenient option to replace the original interface name by the specified name. For instance, if --master specifies bond0,
it is possible to use --rename team0 to change the final interface name to team0.
--ifcfg
Set the output format to ifcfg config style. [default]
--json Set the output format to JSON style. See teamd.conf(5) for further details.
--bonding_opts '<bonding options>'
Specify the bonding options to be converted instead of reading them from the ifcfg file.
--port <interface>
Set the specified interface as a team port.
--configdir <directory>
Change the ifcfg configuration path from /etc/sysconfig/network-scripts to the specified <directory>.
--outputdir <directory>
Set the output directory to <directory>.
--stdout
Print the result to the screen instead of writing to files.
--debug
Increase the debugging level.
--quiet
Disallow any messages to be printed to console.
--version
Print tool version to console and exit.
--help Print help text to console and exit.
--examples
Print common usage examples to console and exit.
EXAMPLES
To convert the current 'bond0' ifcfg configuration to team ifcfg:
# bond2team --master bond0
To convert the current 'bond0' ifcfg configuration to team ifcfg renaming the interface name to 'team0'. Caution : firewall rules, alias
interfaces, etc., that might be tied to the original interface name can break after the renaming because the tool will only change the
ifcfg file, nothing else.
# bond2team --master bond0 --rename team0
To convert given bonding parameters with ports without any ifcfg:
# bond2team --bonding_opts 'mode=1 miimon=500 primary=eth1 primary_reselect=0' --port eth1 --port eth2 --port eth3 --port eth4
For more examples, see the option --examples.
CAVEATS
The tool will not convert any other configuration which might be tied to the current setup. For instance, firewall rules, alias interfaces,
bridges, and so on.
AUTHOR
Flavio Leitner is the original author of the tool. Jiri Pirko is the original author and current maintainer of libteam.
SEE ALSO teamd(8), teamdctl(8), teamd.conf(5), teamnl(8)libteam 2013-07-18 BOND2TEAM(1)