06-06-2017
Welcome trevian3969,
Does the software write to tty00 or to /dev/console? You can redirect the system console through the smit menus to tty02, but sadly I don't have a server available to walk you through it. That might be a lower risk than other options.
Did your previous configuration have a similar dual serial-port board that has been replaced?
If so, you might get away with deleting all the tty devices with rmdev -dl tty00 etc. and then running cfgmgr -S to rediscover them, however you would need to be connected over the network.
Perhaps you could try deleting tty00 & tty03 and running cfgmgr first to see if that moves the one you are not plugged in to.
Important
Before you start, make sure you have a working and tested disaster recovery plan with up to date backups, just in case you server fails to boot.
I hope that this helps,
Robin
This User Gave Thanks to rbatte1 For This Post:
10 More Discussions You Might Find Interesting
1. Programming
Hai there,
Can any one provide me with a ansi c source code for
opening com1 or com2 and read data. The port is connected to
another serial communication device on rs232 port.
The o/s is Sco Unix 5.0.6
Matter urgent
Viswanath (0 Replies)
Discussion started by: viswanath
0 Replies
2. Solaris
hi
i am using solaris 9 on sparc .
i was wondering if there was a command to control my serial interface , as to send a signal periodically every interval of time to the input of a 555 timer .
thanks for your help .... (0 Replies)
Discussion started by: ppass
0 Replies
3. Solaris
Hi,
I am working with Sun Solaris 9 Sparc,Sun-Blade-100.In my application,I need to monitor the UPS using Serial port.
When I am using JRE 1.4 in my application,I am able to monitor it but when I am upgrading the JRE version from 1.4 to JRE1.6. I am not able to monitor the UPS.It is showing the... (1 Reply)
Discussion started by: smartgupta
1 Replies
4. Programming
Hello!
Can someone advice me which method I will use if I want to communicate with device via RS232 serial port with this requirements:
1. Serial port is opened in non-canonical mode.
2. All the time I need to check is there something to read.
3. If I have to write something I need to write it... (6 Replies)
Discussion started by: jvrlic
6 Replies
5. AIX
Hi,
How can i configure my modem in AIX thru serial port (sa0-->tty0)
I have two port serial card configured as sa0
I created tty1 which port is tty0 and which port is tty1 how can i know?? (1 Reply)
Discussion started by: pchangba
1 Replies
6. Solaris
What is the serial port on the T5140 used for. (4 Replies)
Discussion started by: pgsanders
4 Replies
7. Shell Programming and Scripting
Hi,
I have a external board connected to my serial port. I need to execute "shutdown -r now" command when system boot up. When system boots up it requires a username ans password. Then I need to run my command. I can use rc script but that is rebooting system before it asks for username and... (0 Replies)
Discussion started by: charlie.arya
0 Replies
8. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
9. Solaris
Hello,
I have an unloaded T5140 machine and want to access the ILOM for the first time and subsequently the network port after that., and then load Solaris 10 the final January 2011 build.
The first part is what confuses me -the cabling.
I am coming from a Windows machine (w/appropriate... (5 Replies)
Discussion started by: joboy
5 Replies
10. AIX
HI,
Does anyone installed a GPS from his Serial port to an IBM Server serial port with AIX 5.X
I would like the rs232 configuration you used on the GPS, and the ttys configuration from your server.
Thanks in advance !!! (8 Replies)
Discussion started by: trevian3969
8 Replies
TERM(1) General Commands Manual TERM(1)
NAME
term - turn PC into a dumb terminal [IBM]
SYNOPSIS
term [baudrate] [parity] [bits_per_character] [-dial_string] [device]
EXAMPLES
term 2400 # Talk to modem at 2400 baud
term 1200 7 even # 1200 baud, 7 bits/char, even parity
term 8 9600 /dev/tty01
# 9600 baud, 8 bits/char, no parity, use tty01
term -atdt12345 /dev/tty01
# Start with a command to dial out
DESCRIPTION
Term allows MINIX to talk to a terminal or modem over RS232 port 1. The program first sets the baudrate, parity and character length, and
then forks. The parent sits in a loop copying from stdin (usually the console's keyboard), to the terminal or modem (/dev/tty00). The
child sits in a loop copying from the terminal or modem (/dev/tty00) to standard output. Thus when RS232 port 1 is connected to a modem,
every keystroke typed on the keyboard is sent to the modem, and every character arriving from the modem is displayed. Standard input and
output may be redirected, to provide a primitive file transfer program, with no checking. Any argument that starts with a minus ('-') is
sent out to the modem, usually to dial out. Term accepts several commands that are formed by typing the escape character, CTRL-], and a
letter. Type CTRL-]? to see a list of commands. The subshell command is very important, it allows you to type in a ZMODEM command to
transfer data. Do not quit term to do this, or your modem line will be reset! Term keeps the modem line open on file descriptor 9 while
running the subshell, so you can type
<&9 >&9
at the end of your ZMODEM command to connect it to the modem.
Important note: to use term, it is essential that /etc/ttytab is configured so that there is no shell hanging on /dev/tty01. If there is,
both the shell and term will try to read from /dev/tty01, and nothing will work.
SEE ALSO
rz(1), sz(1).
TERM(1)