Sponsored Content
Full Discussion: Disk Failure
Operating Systems HP-UX Disk Failure Post 74031 by SemiOfCol on Tuesday 7th of June 2005 11:31:18 AM
Old 06-07-2005
Disk Failure

I am new to being a Unix admin and have a question about replacing some hardware. I have a K class box using HP-UX 10.20 with three disks. Two of the drives are in one logical volume. Every 3 or 4 days, the syslog is showing that one of these drives is experiencing "POWERFAILED" and then recovering a few seconds or minutes later. My manager feels that the drive should be replaced.

From reading the documentation, it seems to me that I can shutdown, replace the one drive that is failing, and then restore the whole logical volume. Do I need to re-create the logical volume before doing a restore? Are there any other steps I need to take when replacing only 1 drive when the volume group and logical volume encompasses 2 drives?

Thank you in advance for any help.

;
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Disk failure

is there anu way by which i can find out if all the disks on the system are working ? Milind Shauche. (2 Replies)
Discussion started by: shauche
2 Replies

2. Filesystems, Disks and Memory

Looking for a solution to disk failure!

Hi people, I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to get... (1 Reply)
Discussion started by: adam466
1 Replies

3. Filesystems, Disks and Memory

Looking for a solution to disk failure!

Hi people, I have been using my disk for quite a long time but the other day I heard the drive making some noise and had to restart the system again. But when I did that the disk would not boot and I fear that the data might be deleted or lost. So, if you people have any know about the ways to... (2 Replies)
Discussion started by: christopher4
2 Replies

4. Solaris

SAN disk failure

hi all, have a solaris 9 OS and a SAN disk which used to work fine is not getting picked up by my machine. can anyone point out things to check in order to troubleshoot this ?? thanks in advance. (3 Replies)
Discussion started by: cesarNZ
3 Replies

5. Red Hat

How to monitor HP server hard disk failure ?

in red hat 4, 5 any one know any commands or any scritps to monitor HP DL 380 G5/6 server and trigger alarm when hard disk failed. thanks for all support ---------- Post updated at 02:45 PM ---------- Previous update was at 12:00 PM ---------- does HP ProLiant Support Pack support is... (4 Replies)
Discussion started by: maxlee24
4 Replies

6. Solaris

Poor disk performance however no sign of failure

Hello guys, I have two servers performing the same disk operations. I believe one server is having a disk's impending failure however I have no hard evidence to prove it. This is a pair of Netra 210's with 2 drives in a hardware raid mirror (LSI raid controller). While performing intensive... (4 Replies)
Discussion started by: s ladd
4 Replies

7. UNIX for Advanced & Expert Users

RAID5 multi disk failure

Hi there, Don't know if my title is relevant but I'm dealing with dangerous materials that I don't really know and I'm very afraid to mess anything up. I have a Debian 5.0.4 server with 4 x 1TB hard drives. I have the following mdstat Personalities : md1 : active raid1 sda1 sdd1... (3 Replies)
Discussion started by: chebarbudo
3 Replies

8. Linux

Disk is predictive failure but LED is showing green.

Hi Linux Team we use hpacucli ctrl all show config command find out the failure disk. Here command output is showing predictive failure but The Datacenter team are unable to find the correct failure disk. From Datacenter all LEDs are showing green. Datacenter asks us to blink the LED. How... (2 Replies)
Discussion started by: Naveen.6025
2 Replies

9. Linux

0: Failure: (138) Device does not have a disk-config

Hi guys, Any idea why I am getting the below error ? # drbdsetup disk-options 0 --resync-rate=500M 0: Failure: (138) Device does not have a disk-config Some info is; # fdisk -l Disk /dev/sda: 64.4 GB, 64424509440 bytes 64 heads, 32 sectors/track, 61440 cylinders Units =... (0 Replies)
Discussion started by: Junaid Subhani
0 Replies

10. AIX

AIX hard disk failure

Hi all, I have encountered the issue with the hard disk, the disk is failed and need to replace by the new one. As my understanding, this is just to take out the failed disk and insert the new ones, and that's all. But the third party hardware vendor said, there should be another procedure... (9 Replies)
Discussion started by: Phat
9 Replies
LVDISPLAY(8)						      System Manager's Manual						      LVDISPLAY(8)

NAME
lvdisplay - display attributes of a logical volume SYNOPSIS
lvdisplay [-c|--colon] [-d|--debug] [-h|-?|--help] [--ignorelockingfailure] [--maps] [-P|--partial] [-v|--verbose] LogicalVolumePath [Logi- calVolumePath...] DESCRIPTION
lvdisplay allows you to see the attributes of a logical volume like size, read/write status, snapshot information etc. lvs (8) is an alternative that provides the same information in the style of ps (1). lvs is recommended over lvdisplay. OPTIONS
See lvm for common options. -c, --colon Generate colon separated output for easier parsing in scripts or programs. N.B. lvs (8) provides considerably more control over the output. The values are: * logical volume name * volume group name * logical volume access * logical volume status * internal logical volume number * open count of logical volume * logical volume size in sectors * current logical extents associated to logical volume * allocated logical extents of logical volume * allocation policy of logical volume * read ahead sectors of logical volume * major device number of logical volume * minor device number of logical volume -m, --maps Display the mapping of logical extents to physical volumes and physical extents. Examples "lvdisplay -v /dev/vg00/lvol2" shows attributes of that logical volume. If snapshot logical volumes have been created for this original logical volume, this command shows a list of all snapshot logical volumes and their status (active or inactive) as well. "lvdisplay /dev/vg00/snapshot" shows the attributes of this snapshot logical volume and also which original logical volume it is associated with. SEE ALSO
lvm(8), lvcreate(8), lvscan(8) Sistina Software UK LVM TOOLS 2.02.44-cvs (02-17-09) LVDISPLAY(8)
All times are GMT -4. The time now is 07:46 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy