10 More Discussions You Might Find Interesting
1. AIX
Hello,
POWER7 machine.
4 x 1Gbit port ethernet adapter is dedicated to vios. 8023ad etherchannel is created using those 4 ports. Etherchannel adapter is shared to lpars using SEA.
If I test network performance directly from vios partition (using iperf) I'm geting nice 4Gbit throughput. But if... (3 Replies)
Discussion started by: vilius
3 Replies
2. AIX
Hi Guys,
I am trying to test an etherchannel failover and switchback.
I did failover from primary to backup adapter, but now I am not able to switch it back to primary.
phcxxxxx:/ > entstat -d ent4 | grep Active
Active channel: backup adapter ... (1 Reply)
Discussion started by: snchaudhari2
1 Replies
3. AIX
Hi,
I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches.
I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels)
But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies
4. AIX
I have few AIX servers in my data center, which have their EtherChannel configured to have a fat pipe (active/active) and a nagios server to monitor the server uptimes. Nagios server pings every server in the data center and we have pretty much every known unix flavor in this data center. When... (3 Replies)
Discussion started by: thenomad
3 Replies
5. AIX
I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches.
How to make this as a redundancy config?
Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies
6. AIX
Hello,
On a partition with AIX 5300-11-01-0944.
1 etherchannel ent9 with aggregation ent3/ent7.
# lsdev |grep ent
...
ent3 Available 07-01 4-Port 10/100/1000 Base-TX PCI-Express Adapter (14106803)
...
ent7 Available 0A-01 4-Port 10/100/1000 Base-TX PCI-Express... (2 Replies)
Discussion started by: Trunk
2 Replies
7. BSD
Hi Buddies!
I need to do a new kind of setting in FreeBSD (i'm a newbie using this OS).
Interface 1 y 2 in Trunk/Etherchannel mode
IP-> xx.xx.xx.xx
netmask-> 255.255.255.0
Anybody can help me with a step by step Guide?.
THANKS A MILLION!!! (1 Reply)
Discussion started by: dagomez09
1 Replies
8. AIX
I have a server with multiple network interfaces. 2 of these interfaces, lets say en2 and en6 make up an etherchannel interface, which let's say en8.
when I run the command
lsattr -El ent8
I can see the designated primary and backup interfaces as ent6 and ent2, in the given order. But... (10 Replies)
Discussion started by: thenomad
10 Replies
9. AIX
I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks. (5 Replies)
Discussion started by: jwholey
5 Replies
10. AIX
Problem description:
On the condition of EtherChannel function of AIX, when the data exchange between the nodes on the network, there sometimes lost datat packets and cause the application failed. Once we deconfig EtherChannel and use the single adapter configuration, the application works... (0 Replies)
Discussion started by: Frank2004
0 Replies