10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
2. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
3. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
4. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
7. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
8. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
9. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
10. Solaris
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies
netstat-nat(1) General Commands Manual netstat-nat(1)
NAME
netstat-nat - Show the natted connections on a linux iptable firewall
SYNOPSIS
netstat-nat [options]
DESCRIPTION
netstat-nat Displays NAT connections managed by netfilter/iptables which comes with the > 2.4.x linux kernels.
The program reads its information from '/proc/net/ip_conntrack' or '/proc/net/nf_conntrack', which is the temporary conntrack-storage of
netfilter.
OPTIONS
-h displays help
-n don't resolve IPs/portnumbers to host/portnames
-p <protocol>
display NAT connections with protocol selection (see /etc/protocols)
-s <source host>
display connections by source IP/hostname
-d <destination host>
display connections by destination IP/hostname
-S display SNAT connections
-D display DNAT connections
-L display only connections to NAT box self (doesn't show SNAT & DNAT)
-R display only connections routed through the NAT box (doesn't show SNAT & DNAT)
-x extended view of hostnames
-r <src|dst|src-port|dst-port|state>
sort connections
-o no output header
-N display NAT box connection information (only valid with SNAT & DNAT)
-v prints version
FILES
/proc/net/ip_conntrack or /proc/net/nf_conntrack
SEE ALSO
http://www.tweegy.nl/projects/netstat-nat/
http://www.netfilter.org/
AUTHOR
netstat-nat has been written by D.Wijsman danny@tweegy.nl
The manual page has been written by marceln@xs4all.nl
July 2002 netstat-nat(1)