diffimg(1) [centos man page]

DIFFIMG(1)						      General Commands Manual							DIFFIMG(1)

NAME

       diffimg - Calculates intersection between two images

SYNOPSIS

       diffimg image1 image2 [outimage]

DESCRIPTION

       diffimg	generates  an image where each pixel is the difference between the corresponding pixel in each of the two source images.  Thus, if
       the source images are the same the resulting image will be black, otherwise it will have regions of non-black where the images differ.

       Currently supports: .png, .gif, .jpg, and .ps by using ghostscript

AUTHOR

       diffimg was written by John Ellson <ellson@research.att.com>

       This manual page was written by David Claughton <dave@eclecticdave.com>, for the Debian project (but may be used by others).

								   Jan 31, 2010 							DIFFIMG(1)

IDIFF(1)						      General Commands Manual							  IDIFF(1)

NAME

       idiff - compare two images

SYNOPSIS

       idiff [options] image1 image2

DESCRIPTION

       The idiff utility is invoked as follows:

       idiff [options] image1 image2

       Where  input1  and  input2  are	the  names of two image files that should be compared. They may be of any format recognized by OpenImageIO
       (i.e., for which image-reading plugins are available).

       If the two input images are not the same resolutions, or do not have the same number of channels, the comparison will return FAILURE  imme-
       diately and will not attempt to compare the pixels of the two images. If they are the same dimensions, the pixels of the two images will be
       compared, and a report will be printed including the mean and maximum error, how many pixels were above the warning and failure thresholds,
       and whether the result is PASS, WARNING, or FAILURE. For example:

       $ idiff a.jpg b.jpg
       Comparing "a.jpg" and "b.jpg"
	 Mean error = 0.00450079
	 RMS error = 0.00764215
	 Peak SNR = 42.3357
	 Max error = 0.254902 @ (700, 222, B)
	 574062 pixels (82.1%) over 1e-06
	 574062 pixels (82.1%) over 1e-06
       FAILURE

       The  "mean  error"  is the average difference (per channel, per pixel). The "max error" is the largest difference in any pixel channel, and
       will point out on which pixel and channel it was found. It will also give a count of how many pixels were above	the  warning  and  failure
       thresholds.

       The  metadata of the two images (e.g., the comments) are not currently compared; only differences in pixel values are taken into considera-
       tion.

       For a complete description, see /usr/share/doc/libopenimageio-dev/openimageio.pdf.gz.

OPTIONS

       --help Print help message

       -v     Verbose status messages

       -a     Compare all subimages/miplevels

   Thresholding and comparison options
       -fail %g
	      Failure threshold difference (0.000001)

       -failpercent %g
	      Allow this percentage of failures (0)

       -hardfail %g
	      Fail if any one pixel exceeds this error (infinity)

       -warn %g
	      Warning threshold difference (0.00001)

       -warnpercent %g
	      Allow this percentage of warnings (0)

       -hardwarn %g
	      Warn if any one pixel exceeds this error (infinity)

       -p     Perform perceptual (rather than numeric) comparison

   Difference image options
       -o %s  Output difference image

       -od    Output image only if nonzero difference

       -abs   Output image of absolute value, not signed difference

       -scale %g
	      Scale the output image by this factor

SEE ALSO

       iconvert(1), igrep(1), iinfo(1), iprocess(1), iv(1), maketx(1), oiiotool(1).

AUTHOR

       OpenImageIO was written by Larry Gritz and the other authors and contributors.

       This manual page was written by IRIE Shinsuke <irieshinsuke@yahoo.co.jp>, for the Debian project (and may be used by others).

								   May 19, 2012 							  IDIFF(1)