COROSYNC-QUORUMTOOL(8) System Manager's Manual COROSYNC-QUORUMTOOL(8)NAME
corosync-quorumtool - Set and display quorum settings.
SYNOPSIS
corosync-quorumtool [-s] [-m] [-l] [-p] [-v votes] [-n nodeid] [-e expected] [-h] [-i] [-V]
DESCRIPTION
Display the current state of quorum in the cluster and set vote quorum options.
OPTIONS -s show quorum status
-m constantly monitor quorum status
-l list nodes
-v <votes>
change the number of votes for a node *
-n <nodeid>
optional nodeid of node for -v
-e <expected>
change expected votes for the cluster *
-H show nodeids in hexadecimal rather than decimal
-i show node IP addresses instead of the resolved name
-p when used with -s or -l, generates machine parsable output
-h (if no other argument)
show this help text
-V show version and exit
* Starred items only work if votequorum is the quorum provider for corosync
SEE ALSO corosync_overview(8), votequorum_overview(8),
AUTHOR
Angus Salkeld
2012-01-12 COROSYNC-QUORUMTOOL(8)
Check Out this Related Man Page
VOTEQUORUM_QDISK_REGISTER(3) Corosync Cluster Engine Programmer's Manual VOTEQUORUM_QDISK_REGISTER(3)NAME
votequorum_qdisk_register - Registers a new quorum device
SYNOPSIS
#include <corosync/votequorum.h>
int votequorum_qdisk_register(votequorum_handle_t handle, char * name, unsigned int votes);
DESCRIPTION
The votequorum_qdisk_register is used to register a new quorum device. A quorum device is an external way of adding votes to a small clus-
ter. The quorum device is, in effect, a pseudo node in the cluster that provide votes based on some external device, usually a shared disk
partition or perhaps a network router.
This call creates the device but does not mark it active. votequorum_qdisk_poll must be called for the votes to be included in the quorum
calculation.
Note that it is the responsibility of the quorum device subsystem (not provided as part of votequorum) to keep all nodes informed of the
quorum device status.
RETURN VALUE
This call returns the CS_OK value if successful, otherwise an error is returned.
ERRORS
The errors are undocumented.
SEE ALSO votequorum_overview(8), votequorum_initialize(3), votequorum_finalize(3), votequorum_dispatch(3), votequorum_fd_get(3), votequo-
rum_qdisk_poll(3), votequorum_qdisk_unregister(3), votequorum_qdisk_getinfo(3),
corosync Man Page 2009-01-26 VOTEQUORUM_QDISK_REGISTER(3)
Hi all,
I would like to ensure that a volume group has an effective quorum setting of 1 (or off). I know you can change the quorum setting using the chvg -Q command but want to know if the setting has been changed before the vg was varied on or a reboot.
In other words how can I ensure that... (3 Replies)
Hello folks,
I have a question that if i type ls command and type echo $? it always show "0", how i could do this change that when i type ls it will show me 1, actually i want to change the return code of commands from 0 to 1.
Thanks
Bash (5 Replies)
Hello all,
I have two twins Proliant DL580 G3 with RHEL4U4 clustered with Oracle RAC with two nics working in each one.
All nics have the same firmware, driver and type of physical cable connected (Cat 5E). All ports of the switch have the same configuration but only one of the nics of only... (9 Replies)
Hi all
Just a question about quorum.
I am running AIX 5.3
Rootvg has 2 PV - not mirrored. quorum is switched on.
What happens when one disk fails?, can i replace the disk and bring the entire VG back up. with all the data intact. knowing that the VG will be unavailable until i replace the... (3 Replies)
Hi all, i have 3 nodes cluster (Centos 5 cluster suit) with out quorum disk,
node vote = 1,
the value of a quorum = 2,
when 2 nodes going offline, cluster services are destoys.
How i can save the cluster and all services(move all services to one alive node)
with out quorum disk when other... (3 Replies)
I can get my AIX servers to show up in SCOM but I'm struggling with running personal scripts and have the result of these scripts show up in SCOM.
I'm currently using BigBrother and I've written some scripts for BB. I would like to convert these scripts to something that can be used in SCOM.
... (0 Replies)
I read from gpfs implementation guide about node quorum with tie-breaker disks:
In my testing environment, I have 4 AIX as quorum nodes, each node connected to 3 GPFS disks. All the 3 disks are configured to be tie-breaker disks.
Then, I disconnect the network of 2 nodes, and then all gpfs file... (0 Replies)
AudioScope.sh has now had 2 votes of 5 stars.
It has also been thanked in the latest upload...
Although I know who thanked this kids project, and I have personally thanked that person,
this is a public thank you to the two anonymous people who have voted it 5 stars.
Thank you.
It has... (0 Replies)
Hi
I need to know what are the precaution we should take during quorum server reboot as this quorum server is providing quorum devices to five different solaris two node clusters.
Also let me know do I have to follow below procedure as well before and after reboot of quorum server
Do I... (3 Replies)