ich_pata_cable_detect(9) [centos man page]

ICH_PATA_CABLE_DETEC(9) 					ata_piix Internals					   ICH_PATA_CABLE_DETEC(9)

NAME

       ich_pata_cable_detect - Probe host controller cable detect info

SYNOPSIS

       int ich_pata_cable_detect(struct ata_port * ap);

ARGUMENTS

       ap
	   Port for which cable detect info is desired

DESCRIPTION

       Read 80c cable indicator from ATA PCI device's PCI config register. This register is normally set by firmware (BIOS).

LOCKING

       None (inherited from caller).

AUTHOR

       Jeff Garzik
	   Author.

COPYRIGHT

Kernel Hackers Manual 3.10					     June 2014						   ICH_PATA_CABLE_DETEC(9)

CZ(4)							   BSD Kernel Interfaces Manual 						     CZ(4)

NAME

     cz -- Cyclades-Z series multi-port serial adapter device driver

SYNOPSIS

     cz* at pci? dev ? function ?

DESCRIPTION

     The cz device driver supports the Cyclades-Z series of multi-port serial adapters.  The Cyclades-Z is an intelligent serial controller com-
     prising:

	   o   PLX9060ES PCI bus interface

	   o   Xilinx XC5204 FPGA

	   o   IDT R3052 MIPS CPU

     The MIPS CPU runs firmware provided by the device driver.	Communication with the MIPS is performed by modifying data structures located in
     board local RAM or host RAM.

     The Cyclades-Z comes in three basic flavors:

	   o   Cyclades-8Zo rev. 1 -- This is an older 8-port board with no FPGA.  The serial ports are provided by an octopus cable.

	   o   Cyclades-8Zo rev. 2 -- This is the newer 8-port board.  The serial ports are provided by an octopus cable.

	   o   Cyclades-Ze -- This is the expandable version of the Cyclades-Z.  It uses an HD-50 SCSI cable to connect the board to a 1U rack
	       mountable serial expansion box.	Each box has 16 RJ45 serial ports, and up to 4 boxes may be chained together, for a total of 64
	       ports.  Boxes 3 and 4 require their own external power supply, otherwise the firmware will refuse to start (as it cannot communi-
	       cate with the UARTs in those boxes).

     The Cyclades-Z has several features to improve performance under high serial I/O load:

	   o   The board may operate in interrupt-driven mode or polled mode to reduce interrupt load.

	   o   Each channel has a large input and output buffer.

	   o   Each channel may be programmed to generate an interrupt based on reception of a specific character, e.g. a PPP End-Of-Frame charac-
	       ter.

	   o   The MIPS CPU on the board performs all flow-control handling.

FILES

     /dev/ttyCZnnnn -- dial-in (normal) TTY device
     /dev/dtyCZnnnn -- dial-out TTY device

SEE ALSO

     pci(4), termios(4), tty(4)

HISTORY

     The cz driver first appeared in NetBSD 1.5.

AUTHORS

     The cz driver was written by Jason R. Thorpe <thorpej@zembu.com> and
     Bill Studenmund <wrstuden@zembu.com> of Zembu Labs, Inc.

BUGS

     The cz driver does not currently implement communication via host RAM.  While this may improve performance by reducing the number of PCI mem-
     ory space read/write cycles, it is not straightforward to implement with the current bus_dma(9) API.

     Interrupt mode has not been tested.

     There is no support for reading or writing the EEPROM connected to the PLX PCI bus controller.

BSD
								   May 17, 2000 							       BSD