ADD_DS.PL(1) General Commands Manual ADD_DS.PL(1)NAME
add_ds.pl - program to add datasources to an existing RRD
SYNOPSIS
add-ds.pl <add'l ds> [default_val] [type] [heartbeat] [rrdmin] [rrdmax] < file.xml
DESCRIPTION
<add'l ds> number of additional datasources
[default_val] default value to be entered in add'l fields
[type] type of datasource (i.e. COUNTER, GAUGE...)
[heatbeat] length of time in seconds before RRD thinks your DS is dead
[rrdmin] minimum value allowed for each datasource
[rrdmax] max value allowed for each datasource
Options are read in order, so if you want to change the default heartbeat, you need to specify the default_val and type as well, etc.
Output goes to STDOUT.
SEE ALSO add_txrx(1), event2vrule(1), flowscan(1), ip2hostname(1), locker(1)AUTHOR
This manual page was written by Anibal Monsalve Salazar, for the Debian Project.
ADD_DS.PL(1)
Check Out this Related Man Page
ADD_TXRX(1) General Commands Manual ADD_TXRX(1)NAME
add_txrx - add two new Data Sources called 'tx' and 'rx' to an RRD file
SYNOPSIS
add_txrx <file> ...
DESCRIPTION
This utility is used when upgrading from FlowScan-1.005 (or less) to FlowScan-1.006 (or greater). It is used to add two new Data Sources
to FlowScan ".rrd" files. e.g.:
$ make install # install FlowScan-1.006 in your existing FlowScan dir
$ cd $prefix/graphs
$ add_txrx total.rrd *.*.*.*_*.rrd
tx - a count of the unique source IP addresses
that have transmitted flows
rx - a count of the unique destination IP addresses
that have received flows
These Data Sources will allows FlowScan users to calculate the average number of bytes, packets, and flows per host and to determine the
overall level of activity (in terms of numbers of individual hosts) for each subnet and for the entire campus.
The values will be recorded only if you use the TopN directive with the CampusIO and/or SubNetIO reports. TopN was introduced in FlowS-
can-1.006.
For instance, if you set CampusIO's TopN to a value greater than zero, the tx value in FlowScan's "total.rrd" is the number of unique
source IP addresses (hosts) from which FlowScan has seen outbound flows.
Upgrading your RRD Files
If you are upgrading, it is necessary to add two new Data Sources to the some of your existing RRD files. Before running flowscan, backup
your RRD files, e.g.:
$ cd $prefix/graphs
$ tar cf saved_rrd_files.tar *.rrd
then do this:
$ cd $prefix/graphs
$ ../bin/add_txrx total.rrd [1-9]*.*.*.*_*.rrd
SEE ALSO add_ds.pl(1), event2vrule(1), flowscan(1), ip2hostname(1), locker(1)AUTHOR
This manual page was written by Anibal Monsalve Salazar, for the Debian Project.
ADD_TXRX(1)
I have a huge matrix file containing some 1.5 million rows and 6000 columns. The matrix looks something like this:
1 2 3
4 5 6
7 8 9
3 4 5
I want to add all the numbers in the columns of this matrix and display the result to my stdout. This means that the numbers in the first column are:
... (2 Replies)
Hi,
Just trying to get to grips with sed and awk for some reporting for work and I need some assistance:
I have a file that lists policy names on the first line and then on the second line whether the policy is active or not.
Policy Name: Policy1
Active: yes
Policy... (8 Replies)
version info :
vi availabe with RHEL 5.4
I have a text file with 10,000 lines. I want to copy lines from 5000th line to 7000th and redirect to a file. Any idea how I can do this?
Note:
The above scenario is just an example. In my actual requirement, the file has 14 million lines and I want... (9 Replies)
Hi everyone,
I know the following questions are noobish questions but I am asking them because I am confused about the basics of history behind UNIX and LINUX.
Ok onto business, my questions are-:
Was/Is UNIX ever an open source operating system ?
If UNIX was... (21 Replies)
Hello,
I couldn't find an actual introduction thread, so I decided to just put this here.
I go by d0wngrade online. I have been programming in multiple languages for about 15+ years. I started with standard web design languages like HTML and CSS, but I then advanced from design to development... (2 Replies)
Hi guys...
The first active code line in AudioScope.sh is set -u .
This causes a complete exit if a variable is used/found but has not been allocated at the start of the program.
However, apart from writing code to do the task, is there a switch to to check which variables have been... (17 Replies)
Hi.
In thread https://www.unix.com/shell-programming-and-scripting/267833-grouping-counting.html rovf and I had a mini-discussion on grep and awk.
Here is a demo script that compares the awk and grep approaches for this single problem:
#!/usr/bin/env bash
# @(#) s2 Demonstrate group... (1 Reply)
Hello,
I have to fish out some specific columns from a file based on the header value. I have the list of columns I need in a different file. I thought I could read in the list of headers I need,
# file with header names of required columns in required order
headers_file=$2
# read contents... (11 Replies)
For those interested in installing dash shell on OSX Lion to help test POSIX compliancy of shell scripts, it is quite easy. I did it like this:
If you don't have gcc on your system:
0. Download and install the Command Line Tools for Xcode package from Sign In - Apple *
1. Download the dash... (2 Replies)
Hello and thanks in advance for any help anyone can offer me
I'm trying to learn the find command and thought I was understanding it... Apparently I was wrong. I was doing compound searches and I started getting weird results with the -size test. I was trying to do a search on a 1G file owned by... (14 Replies)
I have data of an excel files as given below,
file1
org1_1 1 1 2.5 100
org1_2 1 2 5.5 98
org1_3 1 3 7.2 88
file2
org2_1 1 1 2.5 100
org2_2 1 2 5.5 56
org2_3 1 3 7.2 70
I have multiple excel files as above shown.
I have to copy column 1, column 4 and paste into a new excel file as... (26 Replies)
Dear All,
Taking a break from Vue.js coding for the site, SEO and YT videos; and hopefully addressing some well deserved criticism from some here that I have been too focused on the visual aspects of the forums versus the substance and the community....
While the "current generation... (9 Replies)
Hi all...
Well guys and gals, I jumped in at the deep end and found things that PERL cannot do by default.
Many tricky terminal escape codes are not catered for so I had to create workarounds.
One thing I searched for was this:
Passing perl variable to shell command
AND, @Neo this was... (15 Replies)