uhd_rx_nogui(1) [debian man page]

UHD_RX_NOGUI(1) 						   User Commands						   UHD_RX_NOGUI(1)

NAME

       uhd_rx_nogui - GNU Radio receiver

SYNOPSIS

       uhd_rx_nogui.py [options]

DESCRIPTION

       Command line GNU Radio receiver that takes signal from a UHD peripheral receiver and sends demodulated audio to the sound device.

OPTIONS

       -h, --help
	      show this help message and exit

       -a ARGS, --args=ARGS
	      UHD device address args , [default=]

       --spec=SPEC
	      Subdevice of UHD device where appropriate

       -A ANTENNA, --antenna=ANTENNA
	      select Rx Antenna where appropriate [default=none]

       -f Hz, --frequency=Hz
	      set receive frequency to Hz [default=none]

       -c Hz, --calibration=Hz
	      set frequency offset to Hz [default=0.0]

       -g dB, --gain=dB
	      set RF gain [default is midpoint]

       -m TYPE, --modulation=TYPE
	      set modulation type (AM,FM) [default=none]

       -o RATE, --output-rate=RATE
	      set audio output rate to RATE [default=32000]

       -r dB, --rf-squelch=dB
	      set RF squelch to dB [default=-50.0]

       -p FREQ, --ctcss=FREQ
	      set CTCSS squelch to FREQ [default=none]

       -O AUDIO_OUTPUT, --audio-output=AUDIO_OUTPUT
	      pcm device name.	E.g., hw:0,0 or surround51 or /dev/dsp

SEE ALSO

       uhd_fft(1) uhd_rx_cfile(1) uhd_siggen(1) uhd_siggen_gui(1)

uhd_rx_nogui 3.5						   December 2011						   UHD_RX_NOGUI(1)

UHD_SIGGEN(1)							   User Commands						     UHD_SIGGEN(1)

NAME

       uhd_siggen - Signal Generator using UHD hardware

SYNOPSIS

       uhd_siggen: [options]

DESCRIPTION

       Command-line signal generator application.

OPTIONS

       -h, --help
	      show this help message and exit

       -a ARGS, --args=ARGS
	      UHD device address args , [default=]

       --spec=SPEC
	      Subdevice of UHD device where appropriate

       -A ANTENNA, --antenna=ANTENNA
	      select Rx Antenna where appropriate

       -s SAMP_RATE, --samp-rate=SAMP_RATE
	      set sample rate (bandwidth) [default=1000000.0]

       -g GAIN, --gain=GAIN
	      set gain in dB (default is midpoint)

       -f FREQ, --tx-freq=FREQ
	      Set carrier frequency to FREQ [default=mid-point]

       -x WAVEFORM_FREQ, --waveform-freq=WAVEFORM_FREQ
	      Set baseband waveform frequency to FREQ [default=0]

       -y WAVEFORM2_FREQ, --waveform2-freq=WAVEFORM2_FREQ
	      Set 2nd waveform frequency to FREQ [default=none]

       --sine Generate a carrier modulated by a complex sine wave

       --const
	      Generate a constant carrier

       --offset=OFFSET
	      Set waveform phase offset to OFFSET [default=0]

       --gaussian
	      Generate Gaussian random output

       --uniform
	      Generate Uniform random output

       --2tone
	      Generate Two Tone signal for IMD testing

       --sweep
	      Generate a swept sine wave

       --amplitude=AMPL
	      Set output amplitude to AMPL (0.0-1.0) [default=0.15]

       -v, --verbose
	      Use verbose console output [default=False]

SEE ALSO

       uhd_siggen_gui(1)

uhd_siggen 3.5							   December 2011						     UHD_SIGGEN(1)