pst(4) [debian man page]

PST(4)							   BSD Kernel Interfaces Manual 						    PST(4)

NAME

     pst -- device driver for Promise Supertrak SX6000

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device pst

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   pst_load="YES"

DESCRIPTION

     This driver is for the Promise Supertrak SX6000 ATA hardware RAID controller.  It supports (in hardware) RAID levels 0, 1, 0+1, 3, 5 and JBOD
     on up to 6 ATA disk drives, including automatic rebuild and hotswap, and supports signalling disk status on LEDs on Promise Superswap disk
     enclosures.  The Supertrak line of controllers does not support non-disk devices.

HARDWARE

     The pst driver supports the Promise Supertrak SX6000 ATA hardware RAID controller.

NOTES

     The pst driver does not support manipulating the RAID from the OS, RAIDs need to be set up from the onboard BIOS.	However, hot swap, hot
     spare, and automatic rebuilds are supported without a reboot.

HISTORY

     The pst driver first appeared in FreeBSD 4.7.

AUTHORS

     The pst driver and man page was written by Soren Schmidt <sos@FreeBSD.org>.

BSD
								 December 14, 2004							       BSD

HPTRR(4)						   BSD Kernel Interfaces Manual 						  HPTRR(4)

NAME

     hptrr -- HighPoint RocketRAID device driver

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device hptrr
	   device scbus
	   device da

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   hptrr_load="YES"

     The following tunables are settable from the loader:

     hw.hptrr.attach_generic
     set to 0 to deny driver attach to chips with generic Marvell (non-HighPoint) PCI identification. These chips are also supported by ata(4).
     Some vendors are using same chips, but without providing RAID BIOS.

DESCRIPTION

     The hptrr driver provides support for HighPoint's RocketRAID based RAID controllers.

     These devices support SATA/ATA disk drives and provide RAID0 (striping), RAID1 (mirroring), and RAID5 functionality.

HARDWARE

     The hptrr driver supports the following RAID controllers:

     o	 RocketRAID 172x series
     o	 RocketRAID 174x series
     o	 RocketRAID 2210
     o	 RocketRAID 222x series
     o	 RocketRAID 2240
     o	 RocketRAID 230x series
     o	 RocketRAID 231x series
     o	 RocketRAID 232x series
     o	 RocketRAID 2340
     o	 RocketRAID 2522

NOTES

     The hptrr driver only works on the i386 and amd64 platforms as it requires a binary blob object from the manufacturer which they only supply
     for these platforms.  The hptrr driver does not work on i386 with pae(4) enabled.

     This driver does not support the RR182x series controller.  See the hptmv(4) manual page for details on support.

     This driver supersedes the older rr232x driver.

SEE ALSO

     ata(4), cam(4), hptmv(4), loader(8)

HISTORY

     The hptrr device driver first appeared in FreeBSD 6.3.

AUTHORS

     The hptrr device driver was written by HighPoint Technologies, Inc., and ported to FreeBSD by Scott Long.	This manual page was written by
     David E. O'Brien.

BUGS

     The hptrr driver does not support manipulating the RAID from the OS, RAIDs need to be set up from the on-board BIOS.

BSD
								 November 8, 2009							       BSD