I need some help adding routes in sco.
I am using SCO Openserver 5.0.4.
Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices.
The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Hi All,
I have a AIX server running v5.2 and its having multiple default routes configured to two seperate gateway.
Here's the output of -- netstat -rn
Routing tables
Destination Gateway Flags Refs Use If PMTU Exp Groups
Route Tree for Protocol Family 2... (2 Replies)
Hi
when I do dtrace -l | awk '{print $2}' I get a list of providers. Some of them are similar providers. I want to receive only once the same provide name.
Is there a way to do it?
thx (2 Replies)
Is there a way to add routes using the add route command in AIX to add different routes and bind them to different NICS installed in the box? (2 Replies)
Hi,
How can i delete the following routes on my OpenBSD 4.1 system?
# route -n show (including only relevant ipv6-routes)
Internet6:
Destination Gateway Flags Refs Use Mtu Interface
::/104 ::1 UGRS 1 0 ... (1 Reply)
I added a static route through smit using:
Communications applications and Services ==>
TCIP/IP ==>
Further Configuration ==>
Static Routes ==>
Add a Static Route ==>
Route Type of host
Filled in Destination Address, Default Gateway Address and Network Interface of en0.
This... (2 Replies)
Hello,
I have two AIX 5.3 servers that are supposedly set up exactly the same. The problem I am having is on one of the servers, it seems dynamic routes are being added mysteriously and non-periodically. This only happens on one server and not the other. Also, there doesn't seem to be a specific... (1 Reply)
Hi guys,
when i use the following code:
open(DEST, ">>DESTINATION_")|| die "$!"; #OPEN FILE FOR WRITING
@contents=@field;
print DEST "@contents\n";
I am creating a file that lookss like this:
Wed May 14 11:42:03 2008 10800 306973223399 19419-NEA 1 1259 1 3 80
What i want to do is... (1 Reply)
Hey Gurus.
My routes add using route add , are lost , after reboot.....where caould i save this routes a dont lost them ? Sun Solaris 10 is my OS.
Thanks in advance,
AGADEA. Unix ADMIN (3 Replies)
Hello,
I have a file Pairs.txt composed of 3 columns. For simplicity, this is the file:
A B C
B D W
X Y Z
Z W K
B A C
Y J Q
F M P
Y X Z
I am trying to reduce the file such that I only keep the first occurrence of any "pair". In the example above, I would only want to keep one... (6 Replies)
My work has a Unix based system that currently has the IP address 192.9.2.25
We recently changed internet providers from DSL to Cable. By doing so, we had to get a new router (Belkin) since the DSL provider had a wireless router/modem in one. With the DSL setup, I was able to change the router's... (2 Replies)
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Hi,
Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Hi All,
Is there a quick way to check whether the current routes on my centos are
persistent or not before rebooting ?
i can take a route -n output but i may completely lost access to my server if the routes are gone.
thanks. (1 Reply)
Hi ,
I have cent os 6.5 and am trying to make few routes permanent for bond:
i have added two routes using below two commands :
/sbin/route add -net 10.0.0.0 netmask 255.0.0.0 gw 10.59.160.128
/sbin/route add -net 0.0.0.0 netmask 0.0.0.0 gw 49.44.52.90
post which route command output is... (5 Replies)