DIVALOAD(8) Linux System Administration DIVALOAD(8)
NAME
divaload - configure Eicon Diva active ISDN card
SYNOPSIS
divaload controller protocol [options]
DESCRIPTION
divaload is used to setup the Eicon Diva card for the proper configuration.
OPTIONS
controller
selects the controller (card). This can be either:
-c n
where n is the controller number, or
-all
to operate on all cards.
protocol
can be one of the following:
-f 1TR6 Germany, old protocol for PABX................ PRI & BRI
-f ETSI DSS1, Europe (Germany, ...)................... PRI & BRI
-f FRANC VN3, France, old protocol for PABX............ PRI & BRI
-f BELG NET3, Belgien, old protocol for PABX.......... PRI & BRI
-f SWED DSS1 with CRC4 off, Sweden, Benelux........... PRI
-f NI NI1, NI2, North America, National ISDN........ PRI & BRI
-f 5ESS 5ESS, North America, AT&T..................... PRI & BRI
-f JAPAN Japan, INS-NET64.............................. PRI & BRI
-f ATEL ATEL, Australia, old TPH1962.................. PRI & BRI
-f US North America, Auto Detect.................... BRI
-f ITALY DSS1, Italy................................... PRI & BRI
-f TWAN DSS1, Taiwan.................................. PRI & BRI
-f AUSTRAL Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI
-f 4ESS_SDN 4ESS Software Defined Network................. PRI
-f 4ESS_SDS 4ESS Switched Digital Service................. PRI
-f 4ESS_LDS 4ESS Long Distance Service.................... PRI
-f 4ESS_MGC 4ESS Megacom.................................. PRI
-f 4ESS_MGI 4ESS Megacom International.................... PRI
-f HONGKONG Hongkong...................................... PRI & BRI
-f RBSCAS Robbed Bit Signaling, CAS..................... PRI
-f QSIG QSIG, Intra PABX link protocol................ PRI & BRI
The following options may be given to divaload.
-e [1,2,3]
set Layer 1 framing on PRI Adapter
1 - doubleframing (NO CRC4)
2 - multiframing (CRC4)
3 - autodetection
-x set PRI Adapter in NT mode; default mode is TE
-z set PRI Adapter in High Impedance state until first user application does request interface activation
-l [1...30]
set starting channel number on PRI Adapter. By default the allocation of channels is made on a high-to-low basis. By specifying -l
you select a low-to-high allocation policy (in addition)
-q [0..3]
select QSIG options
0 - CR and CHI 2 Bytes long (default)
1 - CR 1 byte, CHI 2 bytes
2 - CR is 2 bytes, CHI is 1 byte
3 - CR and CHI 1 byte
(CR - Call Reference, CHI - B-Channel Ident.)
-n [0...20]
select NT2 mode and default length of DIDN (DIDN - Direct Inward Dial Number)
-o turn off order checking of information elements
-p [1,2]
establish a permanent connection (e.g. leased line configuration)
1 - TE <-> TE mode, structured line
2 - NT <-> TE mode, raw line
-s [0,1,2,3]
D-Channel Layer 2 activation policy on BRI Adapter
0 - On demand
1 - Deactivation only by NT side, preferred, default
2 - Always active
3 - Always active, mode 2
-t [0...63]
specifies a fixed TEI value (Default is a automatic TEI assignment)
-u select point to point mode on BRI Adapter; uses default TEI '0', NT2 mode is on
-[1...8]oad|osa|spid
BRI Adapter B-Channel options Specify the Originating Address (OAD), Originating Sub-address (OSA) and/or Service Profile Identifier
(SPID) for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)
Example: -1oad 123456 -1spid 1234560001
-d display protocol options summary
-w select alternative protocol code directory.
default directory: "/usr/share/isdn"
-h or -?
help
AUTHOR
manpage written from -h output by Paul Slootman <paul@debian.org>.
divaload 2000/12/02 DIVALOAD(8)