gogoc(8) [debian man page]

GOGOC(8)						    BSD System Manager's Manual 						  GOGOC(8)

NAME

     gogoc -- gogoCLIENT

SYNOPSIS

     gogoc [-h] [-?] [-y] [-n] [-b]
     gogoc [-f config_file] [-i interface_name] [-u interface_name] [-s interface_name] [-r retry_delay]

DESCRIPTION

     gogoc provides a means to configure a tunnel obtained from a tunnel server that supports the tunnel setup protocol (TSP).	gogoc will connect
     to a tunnel server and request a tunnel according to the specifications given in the configuration file.  As a background process, it will
     then monitor the state of the tunnel.  In the event of a timeout, gogoc will establish a new tunnel.

     gogoc currently supports three types of tunnels:

     - v6v4 (IPv6 over IPv4)
	Supported on FreeBSD, NetBSD, OpenBSD, Linux, Windows, Solaris, Darwin and OpenWRT.

     - v6udpv4 (IPv6 over UDP over IPv4)
	Supported on FreeBSD, Linux, Windows, Darwin and OpenWRT.

     - v4v6 (IPv4 over IPv6 (DSTM))
	Supported on FreeBSD and Windows.

ARGUMENTS

     The following options are available:

     -h, -?  Displays a short usage summary and quits.

     -y      Automatically accept server's public key.

     -n      Run as a foreground process.

     -b      Stop trying to reconnect upon first error received.

     -f configuration_file
	     Specifies a different configuration file.
	     Default is /etc/gogoc/gogoc.conf.

     -s interface_name
	     Overrides client_v4 in gogoc.conf(5)

     -i interface_name
	     Overrides if_tunnel_v6v4 in gogoc.conf(5)

     -u interface_name
	     Overrides if_tunnel_v6udpv4 in gogoc.conf(5)

     -r retry_delay
	     Overrides retry_delay in gogoc.conf(5)

SEE ALSO

     gogoc.conf(5)
     http://www.gogo6.com

ACKNOWLEDGMENT

     This software uses code taken from other organizations as :

     - RSA data security for md5.

     - The Apache Software Foundation for Base64 encoding and decoding.

AUTHORS

     gogo6 Inc.
     http://www.gogo6.com
     support@gogo6.com

gogoCLIENT							    May 7, 2007 							gogoCLIENT

Tunnel metadata manipulation action in tc(8)			       Linux			      Tunnel metadata manipulation action in tc(8)

NAME

       tunnel_key - Tunnel metadata manipulation

SYNOPSIS

       tc ... action tunnel_key { unset | SET }

       SET := set src_ip ADDRESS dst_ip ADDRESS id KEY_ID dst_port UDP_PORT [ csum | nocsum ]

DESCRIPTION

       The  tunnel_key	action combined with a shared IP tunnel device, allows to perform IP tunnel en- or decapsulation on a packet, reflected by
       the operation modes UNSET and SET.  The UNSET mode is optional - even without using it, the metadata information will be released automati-
       cally  when packet processing will be finished.	UNSET function could be used in cases when traffic is forwarded between two tunnels, where
       the metadata from the first tunnel will be used for encapsulation done by the second tunnel.  SET mode requires the source and  destination
       ip  ADDRESS  and  the  tunnel  key  id KEY_ID which will be used by the ip tunnel shared device to create the tunnel header. The tunnel_key
       action is useful only in combination with a mirred redirect action to a shared IP tunnel device which will use the metadata (for SET )  and
       unset the metadata created by it (for UNSET ).

OPTIONS

       unset  Unset  the  tunnel metadata created by the IP tunnel device.  This function is not mandatory and might be used only in some specific
	      use cases (as explained above).

       set    Set tunnel metadata to be used by the IP tunnel device. Requires id , src_ip and dst_ip options.	dst_port is optional.

	      id     Tunnel ID (for example VNI in VXLAN tunnel)

	      src_ip Outer header source IP address (IPv4 or IPv6)

	      dst_ip Outer header destination IP address (IPv4 or IPv6)

	      dst_port
		     Outer header destination UDP port

	      [no]csum
		     Controlls outer UDP checksum. When set to csum (which is default), the outer UDP checksum is calculated and included  in  the
		     packets.  When set to nocsum, outer UDP checksum is zero. Note that when using zero UDP checksums with IPv6, the other tunnel
		     endpoint must be configured to accept such packets.  In Linux, this would be the udp6zerocsumrx option for the  VXLAN  tunnel
		     interface.

		     If  using	nocsum	with  IPv6, be sure you know what you are doing. Zero UDP checksums provide weaker protection against cor-
		     rupted packets. See RFC6935 for details.

EXAMPLES

       The following example encapsulates incoming ICMP packets on eth0 into a vxlan tunnel, by setting metadata to VNI 11,  source  IP  11.11.0.1
       and  destination  IP  11.11.0.2,  and  by redirecting the packet with the metadata to device vxlan0, which will do the actual encapsulation
       using the metadata:

	      #tc qdisc add dev eth0 handle ffff: ingress
	      #tc filter add dev eth0 protocol ip parent ffff: 
		flower 
		  ip_proto icmp 
		action tunnel_key set 
		  src_ip 11.11.0.1 
		  dst_ip 11.11.0.2 
		  id 11 
		action mirred egress redirect dev vxlan0

       Here is an example of the unset function: Incoming VXLAN traffic with outer IP's and VNI 11 is decapsulated by vxlan0 and metadata is unset
       before redirecting to tunl1 device:

	      #tc qdisc add dev eth0 handle ffff: ingress
	      #tc filter add dev vxlan0 protocol ip parent ffff:   flower 
		     enc_src_ip 11.11.0.2 enc_dst_ip 11.11.0.1 enc_key_id 11   action tunnel_key unset	action mirred egress redirect dev tunl1

SEE ALSO

       tc(8)

iproute2							    10 Nov 2016 		      Tunnel metadata manipulation action in tc(8)