cvs-debuild(1) [linux man page]

CVS-DEBUILD(1)                                                General Commands Manual                                               CVS-DEBUILD(1)

NAME

       cvs-debuild - build a Debian package using cvs-buildpackage and debuild

SYNOPSIS

       cvs-debuild [debuild options] [cvs-buildpackage options] [--lintian-opts lintian options]

DESCRIPTION

       cvs-debuild  is  a  wrapper  around cvs-buildpackage to run it with debuild as the package-building program.  (This cannot simply be accom-
       plished using the -C option of cvs-buildpackage, as it does not know how to handle all of the special debuild options.)

       The program simply stashes the debuild and lintian options, and passes them to debuild when it is called by cvs-buildpackage.  All  of  the
       standard debuild options may be used (as listed below), but note that the root command specified by any --rootcmd or -r command-line option
       will be passed as an option to cvs-buildpackage.  The first non-debuild option detected will  signal  the  start  of  the  cvs-buildpackage
       options.

       The  selection  of  the  root  command is slightly subtle: if there are any command-line options, these will be used.  If not, then if cvs-
       buildpackage is set up to use a default root command, that will be used.  Finally, if neither of these are the case, then debuild will  use
       its procedures to determine an appropriate command, as described in its documentation.

       See the manpages for debuild(1) and cvs-buildpackage for more information about the behaviour of each.

OPTIONS

       The  following are the debuild options recognised by cvs-debuild.  All cvs-buildpackage and lintian options are simply passed to the appro-
       priate program.  For explanations of the meanings of these variables, see debuild(1).

       --no-conf, --noconf

       --rootcmd=gain-root-command, -rgain-root-command

       --preserve-env

       --preserve-envvar=var, -evar

       --set-envvar=var=value, -evar=value

       --lintian, --no-lintian

       --ignore-dirname, --check-dirname
              These should not be needed, but it is provided nevertheless.

SEE ALSO

       cvs-buildpackage(1), debuild(1), dpkg-buildpackage(1) and lintian(1).

AUTHOR

       This program was written by Julian Gilbey <jdg@debian.org>.

DEBIAN                                                           Debian Utilities                                                   CVS-DEBUILD(1)

CVS-DEBC(1)						      General Commands Manual						       CVS-DEBC(1)

NAME

       cvs-debrelease - upload a cvs-buildpackage/cvs-debuild generated package

SYNOPSIS

       cvs-debrelease [cvs-debrelease options] [--dopts [dupload/dput options]]

DESCRIPTION

       cvs-debrelease  is run from the CVS working directory after cvs-buildpackage or cvs-debuild.  It uses the cvs-buildpackage system to locate
       the .changes file generated in that run.  It then uploads the package using debrelease(1), which in turn  calls	either	dupload  or  dput.
       Note  that  the	--dopts  option  must  be specified to distinguish the cvs-debrelease options from the dupload or dput options.  Also, the
       devscripts configuration files will be read, as described in the debrelease(1) manpage.

       Note that unlike cvs-buildpackage, the only way to specify the source package name is with the -P option; you cannot simply have it as  the
       last command-line parameter.

OPTIONS

       All  current  cvs-buildpackage options are silently accepted; however, only the ones listed below have any effect.  For more details on all
       of them, see the cvs-buildpackage(1) manpage.  All debrelease options (as listed below) are also accepted.

       --dupload, --dput
	      This specifies which uploader program to use; the default is dupload.

       -adebian-architecture, -tGNU-system-type
	      See dpkg-architecture(1) for a description of these options.  They affect the search for the .changes file.  They  are  provided	to
	      mimic the behaviour of dpkg-buildpackage when determining the name of the .changes file.

       -Mmodule
	      The name of the CVS module.

       -Ppackage
	      The name of the package.

       -Vversion
	      The version number of the package.

       -Ttag  The CVS tag to use for exporting sources.

       -Rroot directory
	      Root of the original sources archive.

       -Wwork directory
	      The full path name for the cvs-buildpackage working directory.

       -xprefix
	      This option provides the CVS default module prefix.

       --no-conf, --noconf
	      Do not read any configuration files.  This can only be used as the first option given on the command-line.

       --help, --version
	      Show help message and version information respectively.

SEE ALSO

       cvs-buildpackage(1), debrelease(1) and cvs-debuild(1).

AUTHOR

       cvs-buildpackage  was  written  by  Manoj  Srivastava, and the current version of debrelease was written by Julian Gilbey <jdg@debian.org>.
       They have been combined into this program by Julian Gilbey.

DEBIAN
								 Debian Utilities						       CVS-DEBC(1)