aha(4) [netbsd man page]

AHA(4)							   BSD Kernel Interfaces Manual 						    AHA(4)

NAME

     aha -- Adaptec 154x SCSI adapter driver

SYNOPSIS

     aha0 at isa? port 0x330 irq ? drq ?
     aha* at isapnp?
     aha* at mca? slot ?
     scsibus* at aha?

DESCRIPTION

     The aha driver provides support for the following SCSI adapters:

	   Adaptec AHA-154xA
	   Adaptec AHA-154xB
	   Adaptec AHA-154xC
	   Adaptec AHA-154xCF
	   Buslogic BT-54x
	   Adaptec AHA-1640 (MCA)

SEE ALSO

     cd(4), ch(4), intro(4), mca(4), scsi(4), sd(4), st(4)

BSD
								 November 29, 1994							       BSD

AHA(4)							   BSD Kernel Interfaces Manual 						    AHA(4)

NAME

     aha -- Adaptec SCSI host adapter driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device scbus
	   device aha

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   aha_load="YES"

     In /boot/device.hints:
     hint.aha.0.at="isa"

DESCRIPTION

     This driver provides access to the SCSI bus connected to the Adaptec AHA-154x and AHA-1640 SCSI host adapters.  x is 0 for controllers with-
     out a floppy drive and 2 for controllers that have them.  For optimum performance, Adaptec AHA-174x controllers should be configured in
     enhanced mode and attached via the ahb(4) driver.

     One device hint entry for every card to be attached by the system is required.  Specific values for the port address, IRQ, and DRQ may be
     specified.  If wildcard values are used, the driver will query the device for its current settings and use those.	If the port address is a
     wildcard, the driver consults an internal table of possible port address locations and attaches to the first unattached card it finds.  The
     possible port addresses for this card are 0x330, 0x334, 0x230, 0x234, 0x130, and 0x134.

     The AHA-1640 is an MCA bus card.  Since the MCA bus is a self-identifying bus, no setting of hints is required.

HARDWARE

     The aha driver supports the following SCSI host adapters:

     o	 Adaptec AHA-154xB
     o	 Adaptec AHA-154xC
     o	 Adaptec AHA-154xCF
     o	 Adaptec AHA-154xCP
     o	 Adaptec AHA-1640
     o	 Adaptec AHA-174x in 154x emulation mode
     o	 DTC 3290 SCSI controller in 1542 emulation mode
     o	 Tekram SCSI controllers in 154x emulation mode

SEE ALSO

     ahb(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)

AUTHORS

     The aha driver was ported by M. Warner Losh from the bt driver written by Justin T. Gibbs.

BUGS

     The AHA-154xA card does not support residuals on data transfers.  As a result, this card is no longer supported.

     There have been some reports that the AHA-154xB does not work well under heavy load.

     The AHA-154xCP is a plug and play controller.  However, its resources are set using the on-board BIOS and cannot be moved.  Failures to
     attached for this card are often caused when the resources set in the BIOS conflict.

BSD
								   July 4, 2004 							       BSD