PCCARD(4) BSD Kernel Interfaces Manual PCCARD(4)NAME
pccard -- PC Card bus driver
SYNOPSIS
device pccard
DESCRIPTION
The pccard driver implements the PC Card bus. The pccard driver supports all PC Card bridges in the system.
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.pccard.debug Non-zero values cause more verbose information to be printed when a 16-bit PC Card is inserted or removed.
hw.pccard.cis_debug Non-zero value causes the CIS parsing of the 16-bit PC Card to be much more verbose and include a complete CIS dump.
FILES
/dev/pccard0.cis This exclusive-use device will report all the CIS chains present in a PC Card, if a 16-bit PC Card is inserted in the slot.
Only one user at a time may access the CIS. The CIS is presented as the relevant byte stream from the PC Card. For CIS
tuples in Attribute Memory (the default), only the even locations are presented (the ODD locations are undefined per the
standard). For CIS tuples in Common Memory, every byte is presented to the user. Decoding of the CIS tuples is done via a
userland program. All tuples are presented to the user.
SEE ALSO cardbus(4), pccbb(4)
PC Card Standard, Release 8.
BSD July 9, 2002 BSD
Check Out this Related Man Page
PCCARD(4) BSD Kernel Interfaces Manual PCCARD(4)NAME
pccard -- PC Card bus driver
SYNOPSIS
device pccard
DESCRIPTION
The pccard driver implements the PC Card bus. The pccard driver supports all PC Card bridges in the system.
TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command:
hw.pccard.debug Non-zero values cause more verbose information to be printed when a 16-bit PC Card is inserted or removed.
hw.pccard.cis_debug Non-zero value causes the CIS parsing of the 16-bit PC Card to be much more verbose and include a complete CIS dump.
FILES
/dev/pccard0.cis This exclusive-use device will report all the CIS chains present in a PC Card, if a 16-bit PC Card is inserted in the slot.
Only one user at a time may access the CIS. The CIS is presented as the relevant byte stream from the PC Card. For CIS
tuples in Attribute Memory (the default), only the even locations are presented (the ODD locations are undefined per the
standard). For CIS tuples in Common Memory, every byte is presented to the user. Decoding of the CIS tuples is done via a
userland program. All tuples are presented to the user.
SEE ALSO cardbus(4), pccbb(4)
PC Card Standard, Release 8.
BSD July 9, 2002 BSD
Hey all,
I've bought a few bits from Belkin who seem quite happy to support FreeBSD! Last time I bought a UPS from them and it's still going well :D
I saw this on their website that the 16bit PCMCIA card was supported under FreeBSD:
http://www.belkin.com/network/F5D5020.html
I went to my... (0 Replies)
hello,
i have a problem installing a d-link dwl-510 wireless network card on freebsd 4.8
first, i already successfully installed a dwl- 500 (which is a pcmcia card in a pci card) by adding just a few simple lines to my /etc/rc.conf
pccard_enable="YES"
pccard_mem="DEFAULT"... (0 Replies)
I have a rather peculiar problem in the past 2 weeks. I have a network setup with a linux box acting as a gateway (It is exposed to the internet). Also, there are 2 additional machines that are connected to the gateway (and are not exposed to the outside world). (The gateway has a NAT setup to... (5 Replies)
Ive been fooling around on my spare laptop and put different cores of Fedora on
and the computer uses an ibm a/b/g card
but the os wont recognize the card and doesnt have the software fore it
is there anyway to get the software for the card on the comp or should i buy a card that the os knows? (7 Replies)
I feel like the true definition of a newb but I guess you gotta start somewhere. I installed Gentoo on my laptop yesterday, it's a gnome based environment and I cannot get any wireless internet. The iwconfig and net-setup commands are not being recognized. I'm not sure what the problem is, I've... (1 Reply)
Salamo Alikom after recompilation my kernel does not boot and display msg said : enter full path to bash : /bin/sh i try fsck -r ,fsck -y but the problem is steel . my make.conf : PERL_VER=5.8.8 OVERRIDE_LINUX_BASE_PORT=f8 PERL_VERSION=5.8.8 MODULES_OVERRIDE = linux acpi accf_http pccard msdosfs... (1 Reply)
Hello all :-)
i'm not sure if its a beginner or advanced question but i have the following problem - now for some months
after building a kernel from source (2.6.36 and now 2.6.38) the /dev/sd* entries are not removed if a remove the corresponding usb disk, sd card, what ever. i'm pretty sure... (0 Replies)
I'm a little embarrassed after all these years I've never really successfully compiled my own kernel. I used this guide to make the following files:
linux-headers-5.1.9_5.1.9-1_amd64.deb
linux-image-5.1.9_5.1.9-1_amd64.deb
linux-libc-dev_5.1.9-1_amd64.deb
When I first booted into this... (4 Replies)