mmount(1) General Commands Manual mmount(1)Name
mmount - mount an MSDOS disk
Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.
Description
The mmount command is used to mount an MS-DOS disk. It is only available on Linux, as it is only useful if the OS kernel allows to config-
ure the disk geometry. Its syntax is:
mmount msdosdrive [mountargs]
Mmount reads the boot sector of an MS-DOS disk, configures the drive geometry, and finally mounts it passing mountargs to mount. If no
mount arguments are specified, the name of the device is used. If the disk is write protected, it is automatically mounted read only.
See Also
Mtools' texinfo doc
Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.
* To generate a printable copy from the texinfo doc, run the following commands:
./configure; make dvi; dvips mtools.dvi
* To generate a html copy, run:
./configure; make html
A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html'
* To generate an info copy (browsable using emacs' info mode), run:
./configure; make info
The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.
mtools-4.0.13 28Feb10 mmount(1)
Check Out this Related Man Page
mshowfat(1) General Commands Manual mshowfat(1)Name
mshowfat - shows FAT clusters allocated to file
Note of warning
This manpage has been automatically generated from mtools's texinfo documentation, and may not be entirely accurate or complete. See the
end of this man page for details.
Description
The mshowfat command is used to display the FAT entries for a file. Syntax:
$ mshowfat files
See Also
Mtools' texinfo doc
Viewing the texi doc
This manpage has been automatically generated from mtools's texinfo documentation. However, this process is only approximative, and some
items, such as crossreferences, footnotes and indices are lost in this translation process. Indeed, these items have no appropriate repre-
sentation in the manpage format. Moreover, not all information has been translated into the manpage version. Thus I strongly advise you
to use the original texinfo doc. See the end of this manpage for instructions how to view the texinfo doc.
* To generate a printable copy from the texinfo doc, run the following commands:
./configure; make dvi; dvips mtools.dvi
* To generate a html copy, run:
./configure; make html
A premade html can be found at `http://www.gnu.org/software/mtools/manual/mtools.html'
* To generate an info copy (browsable using emacs' info mode), run:
./configure; make info
The texinfo doc looks most pretty when printed or as html. Indeed, in the info version certain examples are difficult to read due to the
quoting conventions used in info.
mtools-4.0.13 28Feb10 mshowfat(1)
I recently aquired RedHat Linux 7.1 . I currently have 2 harddrives in my computer.. both are running windoze 98.. I was hoping I could make one of them run Linux. Can anyone give me any tips on how I could be able to accomplish this feat? (1 Reply)
Hi:
I need some information about how to configure a dktab archive to make mirroring with ide disk.
I have to know the necesary steps to make that.
Thanks. (2 Replies)
I am using emacs to write c++ code. How to configure it to let the system highlight C++ keywords, variables, etc; and let it automatically indent, just like a common C++ IDE does?
Any suggestions? Thanks! (1 Reply)
Anyone has any doc or ideas on how to bring a oracle mount point into VCS control and how to setup the startup scripts etc? The mount points are using VxVM. I know very basic commands on VCS failover, freezing of resource group etc, but not good in depth knowledge of such. Its urgent. Please help.... (6 Replies)