If the .iso file that you created is less than 1.44mb, then you could try copying the file to a DOS diskette instead of a unix diskette.
This should give you a diskette you can read in XP.
Is the failing disk scsi or ide?
Yet another "hurdle" with copying the iso file to floppy. I have tried four different floppies in the SCO drive, using the dosformat command. Each time the screen says "Formatting..." and the light on the floppy drive is on, but then it fails with: "dosformat: Error formatting drive"
I don't know if it is all of my floppy disks, or the drive just isn't working right. Like I said, all of this hardware is at least 12 years old. I have spare hardware I can experiment with - I have server hardware that was purchased around 2008, it has a CD and floppy drive in it. I could install a new hard drive and set it up as IDE, if I could locate (or I may have) the BTLD driver(s) that would allow me to do a new install of the 5.0.6 software.
At this point, do you think my best shot would be with newer hardware, or trying to go with an installation inside a VM?
There are ide to sata adapters (about $25 startech.com) so you could re-install using a new sata hard drive.
The only btld required would be for the tape drive, which I assume is scsi, and that could be added after the system is running.
I just want to make sure I understand what you're saying. Do you mean to use a new SATA drive with the IDE adapter in the current server hardware? Then reinstall 5.0.6, then restore my backup from tape? I understand this thinking, because the current system has been compromised because of the lost sectors, but I'm just hoping I don't have trouble with the tape drive or the backup files. Let me know if this is what you are suggesting, and it seems like my best option. Thanks - Rob
Yes. Remove the old drive first. Do you know if the driver for the network card is supported directly from the install media, or if you can read it if it is on a diskette?
Even if you have trouble with the tape you are no worse off as you will actually be testing the validity of your backup procedure.
Going back to the question about limiting FTP users, I regret that I don't have a SCO server available to test, however many unix OS variation have a file /etc/ftpusers which work in the reverse to what you might expect. It is a list of accounts that are not allowed to FTP into this server. It is slightly counter intuitive (to me at least ) but I wrote a simple script that I run daily to read /etc/ftpusers.allowed and re-write /etc/ftpusers. It was something like this:-
Would that help? You need to be careful that the input file doesn't have blank lines (which will match every record) or short user ids that are contained within longer ones. Perhaps you should make this a two step process:-
I hope that this is useful on SCO. Apologies if it's not. have a look at th emanual page for ftpd or whatever offers the service for you.
OK, I have my new hard drive installed with the IDE / SATA adapter. Installing from the original SCO 5.0.6 boot disk appears to work fine, I am not linking to any particular driver for the HD and it appears to be recognized. However, when I get to the part about selecting my CD device, the installation does not find the CD. I know from the BIOS that it is attached to the Secondary IDE channel as the Master. Is there some kind of problem with having it as the Secondary Master? I did not change that cable at all, so I know this is how it was configured the last time 5.0.6 was installed. Any ideas why it won't find my CD? I know the CD drive has power, because the tray opens and closes. The "working" light comes on when I insert the CD. However when the installation routine says it is checking the CD the light does not come on. I don't know what to do now. Any help is appreciated.
Hi folks,
I am facing issue of my system (host1) getting hanged after throwing following ntpd messages. I am not able to ssh to the server there after. only option is to restart the host:
Dec 29 02:58:51 host1 ntpd: time reset -0.207907 s
Dec 29 02:58:51 host1 ntpd: synchronisation lost
Dec 29... (0 Replies)
I have a CentOS release 5.2 (Final)host running kernel 2.6.18-92.el5 with at raid 10 that had two mirrored drives fail. The drives were re-inserted and now the raid shows healthy (for now). I tried to mount but got an Input/output error. I then attempted a fsck:
fsck.gfs2 -y /dev/vg_01/uss_vol... (0 Replies)
dear fellows;
i have used ld.so.preload file to override connect() function, dynamic library overriding, it did worked really fine ......
but i went on to struck in a situation ... within the overrided connect() i have used printf once to see IP and Port to whom the connect request is being... (1 Reply)
Hey peeps,
Here is somethin u might find interestin....
Is it possible to recover data from a partition which used to be an ext3 file sytem with some nice forgotten backups, which now is an lvm partion containg root partition of another OS. :)
I couldn't create any mess better than this, can... (2 Replies)
Hi everyone
I'm green AIX user or rather beginner (light green).
Unfortunately I have to restore my system + data from scratch (things happen) and make it up and running. I've never done it before.
Can someone of you provide me with link/procedure/instruction how to do it?
Now I know only:... (3 Replies)
Hi,
Has anyone please got some advise as to how I can make a CD/DVD on an AIX 5.3 system so that it can be fully recoverd just by inserting the backed up system.
The system that I need to recover has no writable devices, not even a tape drive (it wasn't specified by me btw).
I am trying to... (0 Replies)
$ errpt | more
IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION
3074FEB7 0802050205 T H fscsi1 ADAPTER ERROR
B8113DD1 0802050205 T H fcs1 LINK ERROR
B8113DD1 0802050205 T H fcs1 LINK ERROR
3074FEB7 0802050205 T H fscsi0 ADAPTER ERROR
B8113DD1 ... (0 Replies)
Hi all!
I've a strange problem. I would use the GNU Make tool on HPUX 11.11. To archive this, i have compiled the sourcecode and renamed HP make in /usr/bin from make to make_old. Now i have make a softlink from /usr/local/bin/make (GNU version) to /usr/bin/make. All things here are ok, but... (1 Reply)