megaide drivers for SCO 5.0.7

Tags

sco

Operating Systems SCO megaide drivers for SCO 5.0.7

12-05-2007

Registered User

1, 0

Join Date: Dec 2007

Last Activity: 16 February 2009, 11:26 AM EST

Posts: 1

Thanks Given: 0

Thanked 0 Times in 0 Posts

megaide drivers for SCO 5.0.7

I'm attempting to load SCO 5.0.7 on an INTEL S3000AH server board using 2 SATA drives and using the onboard RAID (LSI). I'm not able to find a driver which will work during install, either from LSI or SCO. The LINUX driver is a megaide driver;provided by LSI; and I believe that the SCO driver should be of the same name.

Can anyone assist on this?

Thanks,
Larry Mohr

lmohr83900

View Public Profile for lmohr83900

Find all posts by lmohr83900

Previous Thread | Next Thread

2 More Discussions You Might Find Interesting

1. SCO

Wangtek Tape 5125EN SCO Drivers

Does anybody know where I can get Wangtek Tape Drive 5125EN SCO Drivers? I know that Sco 3.2 r4.2 had it built into the distribution.

2. UNIX for Dummies Questions & Answers

drivers unix 5.01 is compatible with drivers epson fx-2190

Please, I'm From Argentina, And I Need To Know If The Drivers Of Program Unix, Version 5.01 Is Compatible Whit Drivers Of The Printer Epson Fx-2190 Thanks, And I Hope Yuor Answer.

LEARN ABOUT LINUX

mfi

MFI(4)							   BSD Kernel Interfaces Manual 						    MFI(4)

NAME

     mfi -- LSI MegaRAID SAS driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device pci
	   device mfi

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   mfi_load="YES"

DESCRIPTION

     This driver is for LSI's next generation PCI Express SAS RAID controllers.  Access to RAID arrays (logical disks) from this driver is pro-
     vided via /dev/mfid? device nodes.  A simple management interface is also provided on a per-controller basis via the /dev/mfi? device node.

     The mfi name is derived from the phrase "MegaRAID Firmware Interface", which is substantially different than the old "MegaRAID" interface and
     thus requires a new driver.  Older SCSI and SATA MegaRAID cards are supported by amr(4) and will not work with this driver.

     Two sysctls are provided to tune the mfi driver's behavior when a request is made to remove a mounted volume.  By default the driver will
     disallow any requests to remove a mounted volume.	If the sysctl dev.mfi.%d.delete_busy_volumes is set to 1, then the driver will allow
     mounted volumes to be removed.

HARDWARE

     The mfi driver supports the following hardware:

     o	 LSI MegaRAID SAS 1078
     o	 LSI MegaRAID SAS 8408E
     o	 LSI MegaRAID SAS 8480E
     o	 LSI MegaRAID SAS 9260
     o	 Dell PERC5
     o	 Dell PERC6
     o	 IBM ServeRAID M5015 SAS/SATA
     o	 IBM ServeRAID-MR10i
     o	 Intel RAID Controller SROMBSAS18E

FILES

     /dev/mfid?  array/logical disk interface
     /dev/mfi?	 management interface

DIAGNOSTICS

     mfid%d: Unable to delete busy device  An attempt was made to remove a mounted volume.

SEE ALSO

     amr(4), pci(4), mfiutil(8)

HISTORY

     The mfi driver first appeared in FreeBSD 6.1.

AUTHORS

     The mfi driver and this manual page were written by Scott Long <scottl@FreeBSD.org>.

BUGS

     The driver does not support big-endian architectures at this time.

BSD
								   May 12, 2010 							       BSD

SCO