9 More Discussions You Might Find Interesting
1. Linux
I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
2. HP-UX
Hi
Please can someone give me a hint on this, when I list the targets, I see two o them:
#iscsiutil -p
Operational Target Information
------------------------------
Target # 1
-----------
Target Name : iqn.1992-08.com.netapp:sn.142241859
Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies
3. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
4. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
5. UNIX for Advanced & Expert Users
I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies
6. Solaris
Hi all
iscsiadm / iscsitadm.
Ive created two devices on a host.
# iscsitadm list target
Target: 1-disk0
iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0
Connections: 1
Target: 1-disk1
iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies
7. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
8. Solaris
Hi there,
I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server.
*I have re-compiled the linux kernel t support ufs fstype with ro mount support.
filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies
9. BSD
Hello All,
How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies
iscsi(7D) Devices iscsi(7D)
NAME
iscsi - iSCSI software initiator driver
DESCRIPTION
The iscsi driver is a software initiator that transports SCSI commands over TCP/IP as described in RFC 3720. The initiator is administered
through iscsiadm(1M). The iscsi initiator acts as a host adapter driver that attaches the appropriate target driver (for example sd(7D) for
disks or st(7D) for tapes) for devices it discovers. See the System Administration Guide for more information.
FILES
/kernel/drv/iscsi 32-bit ELF kernel driver.
/kernel/drv/sparcv9/iscsi 64-bit SPARC ELF kernel driver.
/kernel/drv/amd64/iscsi 64-bit AMD64 ELF kernel driver.
/kernel/drv/iscsi.conf Driver configuration file.
/etc/iscsi/* iscsi persistent store.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWiscsir, SUNWiscsiu |
+-----------------------------+-----------------------------+
SEE ALSO
iscsiadm(1M), attributes(5)
RFC 3720 Internet Small Computer Systems Interface (iSCSI)
System Administration Guide: Devices and File Systems, Chapter 15
SunOS 5.11 12 April 2005 iscsi(7D)