how can i remove an interface from dladm?
i want to remove ce3 and ce4 which are not even plumbed but still shown in dladm output
dladm show-aggr does not show any output
how to determine key value?
System: SunOS studentrfc 5.10 Generic_144488-01 sun4u sparc SUNW,Netra-440
Best Regards
Thanks in Advance
Last edited by DukeNuke2; 11-26-2010 at 03:01 AM..
you can't remove them from dladm... this command shows all available interfaces in the system. use "ifconfig -a" output.
and if "show-aggr" doensn't show an output, there is no aggregation set confugured.
thanks but the question is still there . how can i remove these ce3 and ce4 from dladm output. ifconfig -a does not show ce3 and ce4 as they are not being used.
Code:
Last edited by DukeNuke2; 11-26-2010 at 11:10 AM..
Hi all,
I have never wondered where is the mapping of the link names to physical device path display under
dladm show-phys until today.
fmadm list reported nic port failure and i am trying to mapped it to the correct linkname in dladm show-link / dladm show-phys to see if the link is... (1 Reply)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Hi all,
I want to remove the remove bracket sign ( ) and put in the separate column I also want to remove the repeated entry like in first row in below input (PA156) is repeated
ESR1 (PA156) leflunomide (PA450192) (PA156) leflunomide (PA450192)
CHST3 (PA26503) docetaxel... (2 Replies)
hello everyone, I'm a new user and unix-beginner.
I've just installer solaris 11 on my home server, disabled some services, created a fallback BE, enabled speedstep, etc
and now I'm trying to create some zones. I'd like to have an exclusive ip zone and, as far as I know, I sould assignate it... (12 Replies)
Can anyone please explain what does these means ?
# dladm show-dev
nxge0 link: up speed: 1000 Mbps duplex: full
nxge1 link: up speed: 1000 Mbps duplex: full
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 ... (6 Replies)
This is my situation
DOS pc serial cable (sl0) Linux Pc eth1
192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router)
I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface.
... (3 Replies)
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Thanks to DukeNuke for the suggestion of dladm before. I was able to upgrade my machine to Solaris 10. I am checking out the sue of dladm, but I am a bit confused. In order to team 2 NIC ports together on my qud ethernet card do I just do this:
dladm create aggr -d ce0 -d ce1 key
Do I need to... (1 Reply)