I am tryin to install a Real Time kernel on my Ubuntu 11.04 Server machine with size 4GB. Before this, I am tryin to install a minimal kernel required in my Ubuntu 11.4 Desktop, but you know, the boot loader cannot load my new kernel. I have also tried the instruction on my Red Hat (CentOS 6) machine and ... again the same problem. boot loader stucks in loading my kernel, (i recall it was saying error with image number)
Here were the instructions:
1. tar xzf linux-2.6.31.6.tar
2. gunzip patch-2.6.31.6-rt19
3. cd linux-2.6.31.6 && patch p1 < ../patch-.6.31.6-rt19
4. make menuconfig (as I need a minimal kernel, I create .config using cat >> .config first)
5. make
6. make modules
7. make modules_install
8. make install (though this give the below output n finishes, but a window prompts n says that fglrx-8.840 cannot be installed or upgraded)
9. I use update-initramfs and five the module folder in /lib/modules as the parameter:
10.
You know, I have also tried compiling this kernel using other methods like:
then running initramfs and giving the /lib/modules/2.6.... as the parameter. Finally updating grub.
but again it cannot load my kernel. Could anyone help me please to compile my new kernel.
Quote:
I would also thank if you mention how I can transfer my compiled kernel in my laptop to the 4GB machine. I think if I copy the compiled bzImage on my laptop there. But don't know about the compiled modules and... I'd thank if you mention everything precisely.
when I choose recovery mode in the boot loader it gives the following notification and it gets stuck till i reboot:
Quote:
loading linux 2.6.31.6-rt19 ...
loading initial ramdisk ...
I also added the nomodeset at the end of linux line but nothing happened.
(stucks)
Regards
Last edited by dr_mabuse; 03-01-2012 at 02:16 PM..
Anyone running CICS TX in a WPAR ?
In my attempts to run CICS TX 5.1.0.1 in a WPAR..... CICS fails to start due to unable to load a CICS IPC Kernel Extension. The Kernel Extension is 64 bit (so not a 32 vs 64 bit issue).
Base system/LPAR is Power8 and AIX 7.1 TL3 SP5. WPAR is versioned... (4 Replies)
Hi everyone,
I am trying to prevent the ehci_hcd kernel module to load at boot time.
Here's what I've tried so far:
1) Add the following line to /etc/modprobe.d/blacklist.conf (as suggested here):
2) Blacklisted the module by adding the following string to
3) Tried to blacklist the module... (0 Replies)
Hello, on my hostserver i see one VPS of mine got load of 200.00 and netstat nothing (not a single blank line on netstat command) after some time, netstat started showing connections, but i see no excessive IP connections.
tail -f /var/log/httpd/access_log shows no activity
/var/log/messages ;... (1 Reply)
Hi gurus
Could anybody tell me which file is read by kernel to set its default system kernal parameters values in solaris. Here I am not taking about /etc/system file which is used to load kernal modules or to change any default system kernal parameter value
Is it /dev/kmem file or something... (1 Reply)
Hi All,
Is there a max number of slabs that can be used per kernel module? I'm having a tough time finding out that kind of information, but the array 'node_zonelists' (mmzone.h) has a size of 5. I just want to avoid buffer overruns and other bad stuff.
Cheers,
Brendan (4 Replies)
hi all
need your help.
I am wrting a script that will load data into the table.
then on another load will append the data into the existing table.
Regards
Ankit (1 Reply)
Hi,
I am seeing very high kernel usage and very high load averages on my system (Although we are not loading much data to our database). Here is the output of top...does anyone know what i should be looking at?
Thanks,
Lorraine
last pid: 13144; load averages: 22.32, 19.81, 16.78 ... (4 Replies)
I'm using SuSE 9.2 Pro and trying to use a program call BestCrypt. I get it installed and type bctool and it says "Kernel modules not loaded". If you need to know anymore about it you can find it at http://www.jetico.com/linux/bcrypt-help/index.htm
linux:/home/chris/Desktop/Xtheater-0.9.2 #... (6 Replies)