10 More Discussions You Might Find Interesting
1. Programming
Hello,
here's my situation: I have a C++ server running on a well known machine and a number of Java clients running on other machines (assumed as unknown) on the same LAN. What I want to achieve is full duplex communication between those applications, in order to exchange complex objects and data... (3 Replies)
Discussion started by: demerzel3
3 Replies
2. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
3. UNIX for Advanced & Expert Users
I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5.
#ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies
4. SuSE
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
Discussion started by: hassan2
4 Replies
5. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
6. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
7. UNIX for Dummies Questions & Answers
Dear Members,
I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies
8. UNIX for Dummies Questions & Answers
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Discussion started by: merlin
4 Replies
9. UNIX for Dummies Questions & Answers
We are using ZIX 4.3.3 and we need to configure the NIC for ful duplexing and we also need to configure it for a TCP/IP default gateway and DNS server to acccess the Interent.
Can you please tell me the commands and procedures for configuring this?
Thanks
Marc (2 Replies)
Discussion started by: marc3483
2 Replies
10. IP Networking
We run Compaq UNIX Tru64 5.1.
After a switch got replaced our ethernet-card was magically set to
half duplex!
We saw, that the card was set to Autonegotiate:
vmunix: ee1: Autonegotiated, 100 Mbps full duplex
So we set the card with ifconfig to 100 Mbps full duplex with the
following... (3 Replies)
Discussion started by: arn_ch
3 Replies
XIRC2PS_CS(4) Kernel Interfaces Manual XIRC2PS_CS(4)
NAME
xirc2ps_cs - Xircom CE2ps (and newer) device driver
SYNOPSIS
insmod xirc2ps_cs.o [pc_debug=n] [full_duplex=n] [irq_list=i,j,...] [if_port=n] [lockup_hack=n]
DESCRIPTION
xirc2ps_cs is the low-level Card Services driver for the Xircom 16-bit PCMCIA ethernet adapters. When this driver is attached to a card,
it allocates the next available ethernet device.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
if_port=n
Selects the transceiver type, for some CE3B-100 cards that lack the ability to autonegotiate. For such cards, a value of 1 selects
10baseT, and 4 selects 100baseT.
full_duplex=n
Selects full duplex mode. The default is 0 (half duplex).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
lockup_hack=n
Enables a hack to avoid lockups on some cards. Use this only if you really have lockup problems with your card.
SEE ALSO
cardmgr(8), pcmcia(5).
BUGS
Please report to <xircom-bugs@isil.d.shuttle.de>
AUTHOR
Werner Koch <werner.koch@guug.de>
1.5 1998/09/15 12:40:59 XIRC2PS_CS(4)