ntp_misc(5) File Formats Manual ntp_misc(5)
NAME
ntp_misc - Miscellaneous Options
broadcastdelay seconds
The broadcast and multicast modes require a special calibration to determine the network delay between the local and remote
servers. Ordinarily, this is done automatically by the initial protocol exchanges between the client and server. In some cases, the
calibration procedure may fail due to network or server access controls, for example. This command specifies the default delay to
be used under these circumstances. Typically (for Ethernet), a number between 0.003 and 0.007 seconds is appropriate.
driftfile driftfile { tolerance ]
This command specifies the complete path and name of the file used to record the frequency of the local clock oscillator. This is
the same operation as the -f command linke option. If the file exists, it is read at startup in order to set the initial frequency
and then updated once per hour or more with the current frequency computed by the daemon. If the file name is specified, but the
file itself does not exist, the starts with an initial frequency of zero and creates the file when writing it for the first time.
If this command is not given, the daemon will always start with an initial frequency of zero. The file format consists of a single
line containing a single floating point number, which records the frequency offset measured in parts-per-million (PPM). The file is
updated by first writing the current drift value into a temporary file and then renaming this file to replace the old version. This
implies that ntpd must have write permission for the directory the drift file is located in, and that file system links, symbolic
or otherwise, should be avoided. The parameter tolerance is the wander threshold to skip writing the new value. If the value of
wander computed from recent frequency changes is greater than this threshold the file will be updated once per hour. If below the
threshold, the file will not be written.
enable [ auth | bclient | calibrate | kernel | monitor | ntp | pps | stats]
disable [ auth | bclient | calibrate | kernel | monitor | ntp | pps | stats ]
Provides a way to enable or disable various system options. Flags not mentioned are unaffected. Note that all of these flags can be
controlled remotely using the ntpdc utility program.
auth Enables the server to synchronize with unconfigured peers only if the peer has been correctly authenticated using either
public key or private key cryptography. The default for this flag is enable.
bclient Enables the server to listen for a message from a broadcast or multicast server, as in the multicastclient command with
default address. The default for this flag is disable.
calibrate
Enables the calibrate feature for reference clocks. The default for this flag is disable.
kernel Enables the kernel time discipline, if available. The default for this flag is enable if support is available, otherwise
disable.
monitor Enables the monitoring facility. See the ntpdc program and the monlist command or further information. The default for this
flag is enable.
ntp Enables time and frequency discipline. In effect, this switch opens and closes the feedback loop, which is useful for test-
ing. The default for this flag is enable.
stats Enables the statistics facility. See the Monitoring Options page for further information. The default for this flag is dis-
able.
includefile includefile
This command allows additional configuration commands to be included from a separate file. Include files may be nested to a depth
of five; upon reaching the end of any include file, command processing resumes in the previous configuration file. This option is
useful for sites that run ntpd on multiple hosts, with (mostly) common options (e.g., a restriction list).
interface [listen | ignore | drop] [all | ipv4 | ipv6 | wildcard | name | address[/prefixlen]]
This command controls which network addresses ntpd opens, and whether input is dropped without processing. The first parameter
determines the action for addresses which match the second parameter. That parameter specifies a class of addresses, or a specific
interface name, or an address. In the address case, prefixlen determines how many bits must match for this rule to apply. ignore
prevents opening matching addresses, drop causes ntpd to open the address and drop all received packets without examination. Multi-
ple interface commands can be used. The last rule which matches a particular address determines the action for it. interface com-
mands are disabled if any -I, --interface, -L, or --novirtualips command-line options are used. If none of those options are used
and no interface actions are specified in the configuration file, all available network addresses are opened. The nic command is an
alias for interface.
leapfile leapfile
This command loads the NIST leapseconds file and initializes the leapsecond values for the next leapsecond time, expiration time
and TAI offset. The file can be obtained directly from NIST national time servers using ftp as the ASCII file pub/leap-seconds.
While not strictly a security function, the Autokey protocol provides means to securely retrieve the current or updated leapsecond
values from a server.
logconfig configkeyword
This command controls the amount and type of output written to the system syslog facility or the alternate logfile log file. All
configkeyword keywords can be prefixed with =, + and -, where = sets the syslogmask, + adds and - removes messages. syslog messages
can be controlled in four classes (clock, peer, sys and sync). Within these classes four types of messages can be controlled:
informational messages (info), event messages (events), statistics messages (statistics) and status messages (status). Configura-
tion keywords are formed by concatenating the message class with the event class. The all prefix can be used instead of a message
class. A message class may also be followed by the all keyword to enable/disable all messages of the respective message class. By
default, logconfig output is set to =syncall +sysevents +sysstatus. Thus, a minimal log configuration could look like this: log-
config =syncstatus +sysevents This would just list the synchronizations state of ntpd and the major system events. For a simple
reference server, the following minimum message configuration could be useful: logconfig =syncall +clockall This configuration will
list all clock information and synchronization information. All other events and messages about peers, system events and so on is
suppressed.
logfile logfile
This command specifies the location of an alternate log file to be used instead of the default system syslog facility. This is the
same operation as the -l command line option.
phone dial1 dial2 ...
This command is used in conjunction with the ACTS modem driver (type 18). The arguments consist of a maximum of 10 telephone num-
bers used to dial USNO, NIST or European time services. The Hayes command ATDT is normally prepended to the number, which can con-
tain other modem control codes as well.
saveconfigdir directory_path
Specify the directory in which to write configuration snapshots requested with ntpq's saveconfig command. If saveconfigdir does not
appear in the configuration file, saveconfig requests are rejected by ntpd.
setvar variable [default]
This command adds an additional system variable. These variables can be used to distribute additional information such as the
access policy. If the variable of the form name = value is followed by the default keyword, the variable will be listed as part of
the default system variables (ntpq rv command). These additional variables serve informational purposes only. They are not related
to the protocol other that they can be listed. The known protocol variables will always override any variables defined via the set-
var mechanism. There are three special variables that contain the names of all variable of the same group. The sys_var_list holds
the names of all system variables. The peer_var_list holds the names of all peer variables and the clock_var_list holds the names
of the reference clock variables.
tinker [ allan allan | dispersion dispersion | freq freq | huffpuff huffpuff | panic panic | step step | stepout stepout ]
This command alters certain system variables used by the clock discipline algorithm. The default values of these variables have
been carefully optimized for a wide range of network speeds and reliability expectations. Very rarely is it necessary to change the
default values; but, some folks can't resist twisting the knobs. The options are as follows:
allan allan
Spedifies the Allan intercept, which is a parameter of the PLL/FLL clock discipline algorithm, in seconds with default 1500
s.
dispersion dispersion
Specifies the dispersion increase rate in parts-per-million (PPM) with default 15 PPM.
freq freq
Spedifies the frequency offset in parts-per-million (PPM) with default the value in the frequency file.
huffpuff huffpuff
Spedifies the huff-n'-puff filter span, which determines the most recent interval the algorithm will search for a minimum
delay. The lower limit is 900 s (15 m), but a more reasonable value is 7200 (2 hours).
panic panic
Spedifies the panic threshold in seconds with default 1000 s. If set to zero, the panic sanity check is disabled and a
clock offset of any value will be accepted.
step step
Spedifies the step threshold in seconds. The default without this command is 0.128 s. If set to zero, step adjustments will
never occur. Note: The kernel time discipline is disabled if the step threshold is set to zero or greater than 0.5 s.
stepout stepout
Specifies the stepout threshold in seconds. The default without this command is 900 s. If set to zero, popcorn spikes will
not be suppressed.
tos [ beacon beacon | ceiling ceiling | cohort {0 | 1} | floor floor | maxclock maxclock | maxdist maxdist | minclock minclock | mindist
mindist | minsane minsane | orphan stratum ]
This command alters certain system variables used by the the clock selection and clustering algorithms. The default values of these
variables have been carefully optimized for a wide range of network speeds and reliability expectations. Very rarely is it neces-
sary to change the default values; but, some folks can't resist twisting the knobs. It can be used to select the quality and quan-
tity of peers used to synchronize the system clock and is most useful in dynamic server discovery schemes. The options are as fol-
lows:
beacon beacon
The manycast server sends packets at intervals of 64 s if less than maxclock servers are available. Otherwise, it sends
packets at the beacon interval in seconds. The default is 3600 s. See the Automatic Server Discovery page for further
details.
ceiling ceiling
Specify the maximum stratum (exclusive) for acceptable server packets. The default is 16. See the Automatic Server Discov-
ery page for further details.
cohort { 0 | 1 }
Specify whether (1) or whether not (0) a server packet will be accepted for the same stratum as the client. The default is
0. See the Automatic Server Discovery page for further details.
floor floor
Specify the minimum stratum (inclusive) for acceptable server packest. The default is 1. See the Automatic Server Discovery
page for further details.
maxclock maxclock
Specify the maximum number of servers retained by the server discovery schemes. The default is 10. See the Automatic Server
Discovery page for further details.
maxdist maxdistance
Specify the synchronization distance threshold used by the clock selection algorithm. The default is 1.5 s. This determines
both the minimum number of packets to set the system clock and the maximum roundtrip delay. It can be decreased to improve
reliability or increased to synchronize clocks on the Moon or planets.
minclock minclock
Specify the number of servers used by the clustering algorithm as the minimum to include on the candidate list. The default
is 3. This is also the number of servers to be averaged by the combining algorithm.
mindist mindistance
Specify the minimum distance used by the selection and anticlockhop algorithm. Larger values increase the tolerance for
outliers; smaller values increase the selectivity. The default is .001 s. In some cases, such as reference clocks with high
jitter and a PPS signal, it is useful to increase the value to insure the intersection interval is always nonempty.
minsane minsane
Specify the number of servers used by the selection algorithm as the minimum to set the system clock. The default is 1 for
legacy purposes; however, for critical applications the value should be somewhat higher but less than minclock.
orphan stratum
Specify the orphan stratum with default 16. If less than 16 this is the stratum assumed by the root servers. See the Asso-
ciation Management page for further details.
trap host_address [port port_number] [interface interfSace_address]
This command configures a trap receiver at the given host address and port number for sending messages with the specified local
interface address. If the port number is unspecified, a value of 18447 is used. If the interface address is not specified, the mes-
sage is sent with a source address of the local interface the message is sent through. Note that on a multihomed host the interface
used may vary from time to time with routing changes. The trap receiver will generally log event messages and other information
from the server in a log file. While such monitor programs may also request their own trap dynamically, configuring a trap receiver
will ensure that no messages are lost when the server is started.
ttl hop ...
This command specifies a list of TTL values in increasing order. up to 8 values can be specified. In manycast mode these values are
used in turn in an expanding-ring search. The default is eight multiples of 32 starting at 31.
SEE ALSO
ntp.conf(5)
The official HTML documentation.
This file was automatically generated from HTML source.
ntp_misc(5)